STMicroelectronics STM32 Development Board Module
เกินview
This manual covers the STM32H743XIH6 / STM32H743 FK743M4-XIH6 / FK743M5-XIH6 core system learning development board module, including key manufacturer details, safety/compliance information, and general setup and operation guidance.
ข้อมูลจำเพาะ
| ชื่อสินค้า | STM32H743XIH6 STM32H743 FK743M4-XIH6 FK743M5-XIH6 Core System Learning STM32 Development Board Module Compatible with OpenMV LCD |
|---|---|
| Model (as listed) | STM32H743XIH6; STM32H743 FK743M4-XIH6; FK743M5-XIH6 (also shown as FK743M4-XIH6 / FK743M5-XIH6) |
| แบทช์/หมายเลขซีเรียล | 1005008125910683 |
| การปฏิบัติตามกฎระเบียบ | CE (2014/35/EU Low Voltage Directive; 2014/30/EU EMC Directive) |
| ระเบียบข้อบังคับ RoHS | Complies with Directive 2011/65/EU and amendment (EU) 2015/863 |
เกี่ยวกับรายการนี้
- High-performance foundation line, ARM Cortex-M4 core with DSP and FPU, 512 Kbytes Flash, 180 MHz CPU, ART Accelerator, Dual QSPI
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Can be powered from USB
- Three LEDs, Two Push-buttons
- Support of wide choice of Integrated Development Environments (IDEs) including IAR, ARM Keil, GCC-based IDEs
การติดตั้ง 
- อ่านคำแนะนำทั้งหมดก่อนใช้งาน
- Before integrating the module, ensure the operational environment aligns with the specified technical parameters and verify compatibility with existing systems.
- Follow established procedures for component placement and connection, and handle the product properly to avoid damage or performance degradation.
- During operation, keep conditions within the prescribed ranges and monitor performance indicators.
- Perform routine maintenance and periodic inspections; store the product in a dry place and keep it away from children.
- คำเตือน: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- ห้ามใช้ผลิตภัณฑ์นี้เพื่อวัตถุประสงค์อื่นนอกเหนือจากการใช้งานที่ตั้งใจไว้
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- อย่าให้โดนน้ำหรือความชื้น
คำแนะนำทั่วไป
คำแนะนำทั่วไป
This product is designed and manufactured in accordance with industry-standard specifications to ensure optimal performance and reliability. Users are expected to adhere to the following guidelines to maximize component functionality and service life.
ขั้นตอนการติดตั้ง
Follow established procedures for component placement and connection. Proper handling is essential to maintain integrity and prevent potential performance degradation.
หมายเหตุการปฏิบัติงาน
During use, maintain conditions within the prescribed ranges. Continuous monitoring of performance indicators is advised to sustain operational excellence.
การบำรุงรักษาและการดูแล
Implement routine maintenance protocols to uphold product standards. Periodic inspections are encouraged to ensure ongoing compliance with quality expectations. Store it in a dry place. Keep away from children.
การปฏิเสธความรับผิดชอบ
The manufacturer assumes no liability for outcomes resulting from non-compliance with these instructions, improper use, or unauthorized modifications. Specifications are subject to change without prior notice.For further details, consult the official documentation or contact our support team.
การแก้ไขปัญหา
- Device damaged or shows issues before use: Inspect the product before each use; do not use it if damaged.
- Safety-related concerns during operation: Do not expose the product to water or moisture; follow installation and operation guidelines to avoid injury.
- Problems potentially related to setup: Review pre-installation considerations—ensure the operational environment matches specified technical parameters and that compatibility with existing systems has been verified.
เอกสาร / แหล่งข้อมูล
 | STM32 Development Board Module |
อ้างอิง
- คู่มือการใช้งานmanual.tools