PHILIPS Smart Wired Wall Switch Module User Manual

PHILIPS Smart Wired Wall Switch Module

ข้อมูลทางเทคนิค

Important purchase and installation tips

ก่อนซื้อ

• Examine how your light switch is installed to determine if the Hue wired wall switch module will work and function properly with your type of light switch.
• Attention! Always make sure your circuit breaker is off before removing the light switch plate.
• Determine if there is enough room in your electrical box to install the Hue wired wall switch module. The Hue wired wall switch module measures 41mm x 37.3 mm x 15 mm(width x depth x height).
• Watch tutorial videos and/or read documentation of the light switch from the manufacturer todetermine if your light switch is suitable.
• Requires Hue bridge and only compatible with Hue light sources
• The product needs a neutral wire to be available

ก่อนการติดตั้ง
Attention! Electrical devices may only be installed and connected by electrically skilled persons.

• For safe installation, commissioning, and operation, read the installation and legal guide before use.
• Always switch off the circuit breaker before any assembly or maintenance.
• Ensure no one switches on the circuit breaker during assembly or disassembly.
• Cover up any live wires.

ระหว่างการติดตั้ง

•  Take a photo of the original light switches’ wiring before removing them. Original wires from your home’s electricity will be terminated with a wire connector.
• Scan the QR code on the manual or product before installation – then complete the onboarding on the Hue app after installation is done.

หลังการติดตั้ง

• แม้แต่อัลamp that is switched off is permanently supplied with mains voltage. When replacing a light source, turn off the circuit breaker.
• Before any maintenance on your light switch, make sure to turn off the circuit breaker.
• Attention! Consult an electrician for support when in doubt.

คำแนะนำด้านความปลอดภัยทั่วไป

เพื่อความปลอดภัยของคุณ

DANGER HAZARD OF ELECTRIC SHOCK
Safe electrical installation must be carried out with proven knowledge in the following areas:

• Connecting installation networks
• การเชื่อมต่ออุปกรณ์ไฟฟ้า
• Handling electric cables
• มาตรฐานความปลอดภัย กฎและข้อบังคับเกี่ยวกับการเดินสายไฟในพื้นที่

อันตราย! ไฟฟ้าช็อตเมื่อสัมผัสชิ้นส่วนที่มีไฟฟ้าอาจถึงแก่ชีวิตได้

• Prepare well, take your time, and avoid distraction
• Use the right equipment to do the installation
• Keep children on a safe distance from any installation and maintenance work
  บันทึก: when one of the above points are not met, do not proceed and consult an electrician or local authority for guidance.
• Application notes for installers, how-to-video, and FAQ’s can be found on our support

Work on electrical installations is, in some countries, only allowed by a qualified electrician. For support, contact a local electrician or authoriThe electrical circuit and attached light source will always be powered after
installation. Turn off the circuit when replacing a light fixture.

คำแนะนำการติดตั้ง

• Attention! Electrical devices may only be mounted and connected by electrically skilled persons.
• For safe installation, commissioning, and operation, the instruction and legal manual with the product must be read.
• Before any assembly or disassembly always switch off the circuit breaker.
• Always make sure nobody can switch on the circuit breaker while working
• It is advised to check that there is no voltage, ground, and shortcut on any parts
• Cover up live wires
• Test that the power is off before proceeding
• Only proceed when above is checked.
• คำแนะนำ: print this manual and cross off the above steps to ensure a safe working environment.

อะไรอยู่ในกล่อง

Excluded elements

Rocker switch 1-way

1. Scan the QR code and follow the steps in the Hue app
2. Always switch off power before you start
3. Remove the switch to access the wiring
4. Make sure there is a neutral wire in the wall box
5. Disconnect the load wire and the line wire
6. Connect the load wire and the line wire to the push-in connector
7. Place a new line wire between L terminal and the switch
8. Place a new line wire between the switch and the additional connector
9. Place a new neutral
10. Place a new load wire between N terminal wire between 1 and the wall box terminal and the switch
11. Fit the Hue module inside the wall box behind your existing switch
12. Remount the switch
13. Restore the main power

• Keep the app open until the product is fully installed and you are guided to the next screen. If needed, please re-scan the QR code on the manual.
• 1-way switching using a rocker type switch is the default for the Hue wall switch module in the Hue app.
• This installation is for connecting a single legacy switch to a Hue module to keep Hue lights reachable.
• For circuit diagrams please review the application notes on our FAQ page.
• In most cases only the 2 disconnected (live) wires and the new line wire must be placed in the provided push-in wire connector.
  เคล็ดลับ! Take a picture before removing the wires to remember the location.
• When adding the module in the Hue app, follow the instructions and select first “One button” and then “Rocker switch” when asked.
  
• For 2-way switching please follow Application notes. In the app, follow the same installation steps for the wall module as regular 1-way switching and select “One button” and “Rocker switch” for both modules when asked.
• For other switching set ups please follow the Application notes available on our support

Rocker switch variants

• A rocker light switch typically has two positions, On and Off, and works like a seesaw.
• We support 1 gang and 2 gang rocker switches per wall switch module.
• There are many variances of light switches and the module works with most common switch types with the following exceptions:
• The module does not work in combination with dimmers and dimming modules.
• If in doubt whether your switch is suitable for installation, contact an electrician for support.

Rocker switch 2-gang

1.  Scan the QR code and follow the steps in the Hue app
2. Always switch off power before you start
3. Remove the switch to access the wiring
4. Make sure there is a neutral wire in the wall box
5. Disconnect the load wire and the line wire
6. Connect the load wire and the line wire to the push-in connector
7. Place a new line wire between L terminal and the switch 8. Place a new line wire between the switch and the additional connector
8. Place a new neutral wire between N terminal and the wall box
9. Place a new load wire between 1 terminal and the switch
10. Place a new load wire between 2 terminal and switch
11. Fit the Hue module inside the wall box behind your existing switch
12. Remount the switch
13. Restore the main power

Keep the app open until the product is fully installed and you are guided to the next screen.

• This installation is for two switches in one frame, controlling two independent groups of lights.
• For circuit diagrams please review the application notes on our FAQ page.

1. In most cases only the 3 disconnected (live) wires and the new line wire have to be added to the provided push-in wire connector. Never add neutral and/or ground to the push-in wire connector.
   Tip! Take a picture before removing the wires to remember the location.
2. You need to use two sets of wiring, one in position 1 and one in position 2 (see image 1) in the module.

• When adding the module in the Hue app, follow the instructions and select first “Two button” and then “Rocker switch” when asked.

Push-in wire connector instructions

1. Select the right (live) wires
   Attention! Do not add neutral or ground wires to the push-in wire connector
2. Straighten the wires (cut when necessary to straighten the wires)
3. Make sure the copper part can be fully inserted into the connector
4. Push the wires into the connector until they are locked securely in place

ความสนใจ!

• No copper should be outside the connector.
• Stranded wires should not be used with the provided connector. (see image 1) Choose an appropriate connector for stranded wires (not provided).

กดปุ่ม

• A push button switch returns to a neutral position directly after being pushed, by means of a spring inside the switch, which is not the case for rocker switches that work like a seesaw.
• From appearance, these could sometimes look very similar to rocker switches or dimmers.
• A push button can not be turned to dim but could sometimes look very similar to a dimmer because of its round shape.
• When it is determined a push button is used, please select single or double push button during the configuration in the app.
• Users will be asked in the app to indicate whether their switches have one or two push buttons, and it will help them identify via animations if unclear.
• Keep the app open until the product is fully installed and you are guided to the next screen.

In the case a wire is inserted in the wrong terminal on the module, there is a way to disconnect the wire from the terminal. Insert a screwdriver in the slot and push slightly to release the wire.