คู่มือการใช้งานเครื่องวัด LCR ​​แบบพกพา RuoShui รุ่น 4080

1. บทนำ

This manual provides detailed instructions for the safe and effective operation of the RuoShui Handheld LCR Meter 4080. This digital bridge multimeter is designed for precise measurement of inductance (L), capacitance (C), and resistance (R) across various test frequencies. It is an essential tool for engineers, technicians, and hobbyists working with electronic components.

Figure 1: RuoShui Handheld LCR Meter 4080 with test leads connected.

2. ข้อมูลด้านความปลอดภัย

Please read and understand all safety warnings and operating instructions before using this instrument. Failure to do so may result in injury or damage to the meter.

• ไม่ต้องสมัครวอลุ่มtage to the input terminals. This device is designed for passive component testing only.
• Always discharge capacitors before testing to prevent damage to the meter and ensure accurate readings.
• ตรวจสอบให้แน่ใจว่าสายทดสอบอยู่ในสภาพดีและเชื่อมต่ออย่างถูกต้อง
• Do not operate the meter in wet environments or near flammable gases.
• If the meter is damaged or malfunctioning, discontinue use immediately and contact support.
• Only use the specified battery type and charging method.

3. สินค้าหมดview

3.1 คุณสมบัติหลัก

• Measurement Capability: Inductance, Capacitance, Resistance, ESR, D, Q, Theta.
• Test Frequencies: 100Hz, 120Hz, 1KHz, 10KHz, 40KHz, 100KHz.
• ความแม่นยำ: 0.2%.
• แสดง: 2.8-inch TFT color display with backlight.
• การเชื่อมต่อ: Mini-USB for PC communication and data acquisition.
• พลัง: Internal Lithium Polymer battery, USB-C charging.
• Measurement Speeds: Fast (4 times/s), Medium (2 times/s), Slow (1 time/s).

รูปที่ 2: เกินview of the RuoShui 4080 LCR Meter's key features including TFT color display, multiple measuring speeds, data hold, silicone protective cover, foldable stand, USB data transmission, PC remote control, automatic shutdown, and low-power rechargeable battery.

3.2 Meter Layout and Controls

Familiarize yourself with the meter's physical components and controls as shown in Figure 3.

Figure 3: Labeled diagram of the RuoShui 4080 LCR Meter's display, buttons, and test terminals.

• หน้าจอแสดงผล: 2.8-inch TFT color display for measurement readings and settings.
• ปุ่มเปิด/ปิด: เปิด/ปิดอุปกรณ์
• ปุ่มถือ: Freezes the current measurement on the screen. A long press shows min/max/average values.
• AUTO/R/C/L/Z Button: Selects the main measurement parameter (Auto, Resistance, Capacitance, Inductance, or Impedance).
• ปุ่ม REC: Activates data recording mode.
• NULL/CAL Button: Offsets displayed values (short press). Initiates calibration procedure (long press).
• X/D/Q/ESR Button: Selects secondary measurement parameters (Reactance, Dissipation Factor, Quality Factor, ESR).
• FREQ Button: Cycles through test frequencies (100Hz, 120Hz, 1KHz, 10KHz, 40KHz, 100KHz).
• LEVEL Button: Adjusts the test signal level (300mV, 600mV, 1000mV).
• อคติฉบับtagปุ่มอี: (Indicated by a specific symbol, often a capacitor with a DC line) Applies a DC bias voltage (0V, 100mV, 300mV, 600mV).
• Direction Keys (Up/Down/Left/Right): เรียกดูเมนูและปรับการตั้งค่าต่างๆ
• ปุ่ม ENTER: ยืนยันการเลือกในเมนู
• ปุ่ม ตลท.: Accesses system settings (Language, Auto-off, Brightness, Beep, Colors, PowerOn).
• AUTO/SER/PAL Button: Toggles between Auto, Series, and Parallel equivalent circuit modes.
• TOL% Button: Activates tolerance comparison mode.
• COMPARE Button: Used in conjunction with TOL% for component sorting.
• ปุ่มความเร็ว: Selects measurement speed (Fast, Medium, Slow).
• ปุ่มช่วง: Selects measurement range (Auto or manual).
• Five-terminal Test Slot: For direct insertion of components.
• Three-terminal Test Jacks: For connecting test leads (Hpot, Lpot, Hcur, Lcur, Guard).
• พอร์ต Mini-USB: For charging and PC communication.

4. การตั้งค่า

4.1 การชาร์จแบตเตอรี่

The LCR Meter 4080 is powered by an internal Lithium Polymer battery. Before first use, or when the battery indicator is low, charge the device using the provided Mini-USB cable and a compatible USB power adapter (not included). The screen will display "In Charging" and the battery level icon during charging. The meter can be used while charging.

รูปที่ 4: ด้านข้าง view of the RuoShui 4080 LCR Meter showing the Mini-USB charging port.

4.2 การเชื่อมต่อสายทดสอบ

For most measurements, use the provided alligator clip test leads. Connect the leads to the three-terminal test jacks at the bottom of the meter. Ensure a secure connection for accurate readings.

• เชื่อมต่อสายสีแดงเข้ากับ ฮปต และ ฮคูร์ terminals (often combined).
• เชื่อมต่อสายสีดำเข้ากับ ลพ็อต และ ลเคอร์ terminals (often combined).
• การ อารักขา terminal can be used for shielded measurements to reduce external interference.

Alternatively, small components can be inserted directly into the five-terminal test slot for quick measurements. This slot is designed for 4-wire measurement, with the drive on the bottom metal lip and sense on the top metal lip.

รูปที่ 5: ระยะใกล้ view of the five-terminal test slot and three-terminal test jacks.

5. คู่มือการใช้งาน

5.1 เปิด/ปิดเครื่อง

กดปุ่มค้างไว้ ปุ่มเปิดปิด (red circle with line) to turn the meter on or off.

5.2 Basic Measurements (L/C/R)

1. Connect Component: Connect the component to be tested using the test leads or insert it into the direct test slot. Remember to discharge capacitors first.
2. Select Main Parameter: กดปุ่ม ออโต้/อาร์/ซี/แอล/ซี button to cycle through automatic detection (AUTO), Resistance (R), Capacitance (C), Inductance (L), or Impedance (Z). In AUTO mode, the meter attempts to identify the component type.
3. Select Test Frequency: กดปุ่ม ความถี่ button to choose the desired test frequency (100Hz, 120Hz, 1KHz, 10KHz, 40KHz, 100KHz). The chosen frequency will be displayed on the screen.
4. Select Measurement Speed: กดปุ่ม ความเร็ว button to select Fast, Medium, or Slow measurement speed. Slower speeds generally provide more stable readings.
5. อ่านการวัด: The primary measurement (L, C, or R) will be displayed prominently on the screen.

Figure 6: Close-up of the LCR Meter's display showing measurement readings.

5.3 Equivalent Circuit Modes (Series/Parallel)

กดปุ่ม AUTO/SER/PAL button to switch between Auto, Series, and Parallel equivalent circuit modes. The appropriate mode depends on the component and test frequency:

• โหมดอนุกรม: Often preferred for low impedance components (e.g., small inductors, large capacitors).
• โหมดคู่ขนาน: Often preferred for high impedance components (e.g., large inductors, small capacitors, resistors).
• โหมดอัตโนมัติ: The meter attempts to select the most suitable mode.

5.4 Calibration (Open/Short Correction)

Calibration helps to remove residual impedance from test leads and fixtures, improving measurement accuracy. It is recommended to perform calibration when changing test leads or frequently for critical measurements.

1. Short Calibration:
   • Connect the provided shorting bar to the test terminals or short the test leads together.
   • กดค้างไว้ NULL/CAL button. The screen will indicate "Short" calibration in progress and show a countdown. This process takes approximately 45 seconds.
2. Open Calibration:
   • Remove the shorting bar or ensure the test leads are open (not touching anything).
   • กดค้างไว้ NULL/CAL button again. The screen will indicate "Open" calibration in progress and show a countdown. This process also takes approximately 45 seconds.

The meter automatically senses the presence or absence of the shorting bar, allowing calibration in either order. Calibration settings can be preserved through power cycles if "PowerOn: Last" is selected in the system settings.

5.5 Secondary Measurement Parameters (ESR, D, Q, X)

กดปุ่ม X/D/Q/ESR button to cycle through secondary measurement parameters displayed below the main reading:

• ESR (Equivalent Series Resistance): Important for evaluating capacitor quality.
• D (Dissipation Factor): Indicates the energy loss in a component.
• Q (Quality Factor): The inverse of the dissipation factor, indicating the efficiency of a reactive component.
• X (Reactance): The imaginary part of impedance.

5.6 Test Signal Level and Bias Voltage

• ระดับการทดสอบ: กดปุ่ม ระดับ button to adjust the RMS test voltage (300mV, 600mV, 1000mV). A higher level can improve signal-to-noise ratio (SNR) for better accuracy, especially for low-value components.
• อคติฉบับtage: ใช้แบบเฉพาะ อคติฉบับtage ปุ่ม (or navigate via arrow keys) to apply a DC bias (0V, 100mV, 300mV, 600mV). This is useful for testing electrolytic capacitors or semiconductors.

5.7 Special Function for Electrolytic Capacitors

The meter includes a dedicated function for electrolytic capacitors. Activating this function typically sets the test level to a fixed 600mV RMS and applies a 1V offset, ensuring the lowest part of the test sine wave remains above ground. Refer to the meter's on-screen prompts or specific button for this function.

5.8 การตั้งค่าระบบ

กดปุ่ม ชุด button to access system settings. Use the ปุ่มทิศทาง to navigate and adjust options:

• ภาษา: Select Chinese or English.
• ปิดอัตโนมัติ: Set automatic power-off time (OFF, 5, 15, 30, 60 minutes).
• สดใส: Adjust backlight brightness in 20% increments.
• เปิดเครื่อง: Choose whether the meter starts with the last settings ("Last") or default settings ("Default").
• ปี๊บ: Configure audible alerts (Off, Key+Notice, Only Notice).
• สี: Select display color scheme (White, Yellow, Cyan, Coral).

6. Remote Communication

The RuoShui 4080 LCR Meter supports remote communication and data acquisition via its Mini-USB port. Connect the meter to a PC using a Mini-USB cable. You may need to install specific driver software provided by RuoShui for your operating system to enable communication. This feature allows for remote control of the meter and logging of measurement data.

Figure 7: The LCR Meter connected to a PC for remote communication and data display.

7. การบำรุงรักษา

7.1 การทำความสะอาด

เช็ดภายนอกมิเตอร์ด้วยผ้านุ่มๆamp cloth. Do not use abrasive cleaners or solvents. Ensure no moisture enters the device.

7.2 พื้นที่จัดเก็บ

Store the meter in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, ensure the battery is partially charged (around 50%) to prolong its lifespan.

7.3 Screen Protection

The screen may come with a protective film. Carefully remove this film for optimal display clarity. Use a soft cloth to clean the screen.

8 การแก้ไขปัญหา

9. ข้อมูลจำเพาะ

หมายเหตุ: ข้อมูลจำเพาะอาจเปลี่ยนแปลงได้โดยไม่ต้องแจ้งให้ทราบล่วงหน้า

10. การรับประกันและการสนับสนุน

For warranty information and technical support, please refer to the documentation included with your purchase or contact RuoShui customer service directly. Contact details can typically be found on the manufacturer's official webไซต์หรือผ่านจุดซื้อของคุณ

ผู้ผลิต: รั่วสุ่ย

หมายเลขรุ่น: HT-LCR Meter-4080