1. บทนำ
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Belltech 152650BK 1.5-inch Lift Kit. Please read this manual thoroughly before beginning installation to ensure safety and optimal performance of your vehicle.
1.1 ข้อมูลด้านความปลอดภัย
- Professional installation is highly recommended for this product.
- Always use appropriate personal protective equipment, including eye protection and gloves, during installation.
- Ensure the vehicle is securely supported on jack stands or a hydraulic lift before performing any work underneath. Never rely solely on a jack.
- Do not modify any components of this kit. Unauthorized modifications can compromise safety and performance.
- After installation, a full wheel alignment must be performed by a qualified technician.
- Check all fasteners for proper torque after the initial installation and again after the first 500 miles of driving.
2. เนื้อหาบรรจุภัณฑ์
Verify that all components listed below are present and undamaged before beginning installation. If any parts are missing or damaged, contact Belltech customer support immediately.
Image: All components of the Belltech 152650BK 1.5-inch Lift Kit, including front strut spacers, rear spacers, sway bar end links, and various bolts and washers.
- Front Strut Spacers (2)
- Rear Spacers (2)
- Sway Bar End Links (2)
- Mounting Hardware (various bolts, nuts, washers)
3. คำแนะนำในการติดตั้ง
This section outlines the general steps for installing the Belltech 152650BK 1.5-inch Lift Kit. It is crucial to refer to a professional service manual for your specific vehicle model for detailed torque specifications and additional procedures.
3.1 เครื่องมือที่จำเป็น
- Vehicle Lift or Heavy-Duty Jack Stands
- ประแจแรงบิด
- Standard Socket Set (Metric and/or SAE as required by vehicle)
- ชุดประแจปากตาย
- แงะบาร์
- Spring Compressor (if required for strut disassembly, consult vehicle service manual)
- ลิ่มล็อคล้อ
- สายวัด
3.2 Front Installation
- Safely secure the vehicle on a lift or jack stands. Remove the front wheels.
- Disconnect the sway bar end links from the strut and lower control arm.
- Remove the upper and lower strut mounting bolts. Carefully remove the entire strut assembly from the vehicle.
- Install the provided front strut spacer onto the top of the factory strut assembly. Ensure proper orientation as per the spacer design and secure with provided hardware.
- Reinstall the modified strut assembly into the vehicle. Secure with factory hardware, but do not fully torque until the vehicle is at ride height.
- Install the new, longer sway bar end links provided in the kit.
- Reattach all other disconnected components. Torque all fasteners to manufacturer specifications once the vehicle is on the ground.
Image: Close-up of a front strut spacer, a key component for achieving the front lift. This component is installed above the factory strut.
Image: Two adjustable sway bar end links, designed to accommodate the increased ride height and maintain proper sway bar function.
3.3 การติดตั้งด้านหลัง
- Safely secure the vehicle on a lift or jack stands. Remove the rear wheels.
- Support the rear axle with a floor jack. Disconnect the lower shock mounts and any other components that may limit axle droop.
- Carefully lower the axle to allow for removal of the factory coil springs.
- Install the provided rear spacers on top of the factory coil springs. Ensure they are seated correctly.
- Reinstall the coil springs with the spacers. Raise the axle and reattach the lower shock mounts and any other disconnected components.
- Torque all fasteners to manufacturer specifications once the vehicle is on the ground.
Image: Four cylindrical rear coil spring spacers, used to achieve the rear lift by being placed above the factory coil springs.
3.4 Post-Installation Procedures
- Reinstall all wheels and torque lug nuts to factory specifications.
- ลดรถลงกับพื้น
- Drive the vehicle a short distance (e.g., 10-20 miles) and then re-check all fasteners for proper torque.
- Perform a professional wheel alignment immediately after installation to ensure proper handling and tire wear.
- Adjust headlight aim as necessary due to the change in vehicle height.
4. ข้อควรพิจารณาในการดำเนินงาน
After installing the lift kit, the vehicle's center of gravity will be higher. This may affect handling characteristics and require adjustments to driving habits.
- Drive cautiously until you become accustomed to the vehicle's new handling and braking characteristics.
- โปรดระวังความสูงของรถที่เพิ่มขึ้นเมื่อเข้าอู่ซ่อมรถ สถานีล้างรถ หรือพื้นที่ที่มีความสูงจำกัด
- If larger tires are installed in conjunction with this lift kit, the speedometer may require recalibration to ensure accurate speed readings.
5. การบำรุงรักษา
Regular maintenance is essential to ensure the longevity and safe operation of your Belltech lift kit.
- Periodically inspect all suspension components, including bolts, nuts, bushings, and spacers, for signs of wear, damage, or corrosion.
- Re-torque all fasteners after the first 500 miles of driving and then every 5,000 miles or during routine vehicle maintenance.
- Keep components clean to prevent the buildup of dirt and debris, which can accelerate wear.
6 การแก้ไขปัญหา
This table provides solutions for common issues that may arise after installation.
| ปัญหา | สาเหตุที่เป็นไปได้ | สารละลาย |
|---|---|---|
| ระดับความสูงของรถไม่เท่ากัน | Improper installation of spacers; component settling. | Verify spacer placement and orientation; re-check all measurements; allow for a short settling period (e.g., 50-100 miles). |
| Unusual Noises (clunking, squeaking) | Loose fasteners; worn bushings; component interference. | Inspect and re-torque all fasteners to specifications; check for proper clearance between components; replace any worn bushings. |
| Poor Handling/Steering | Incorrect wheel alignment; loose steering or suspension components. | Perform a professional wheel alignment; inspect all steering and suspension components for looseness or damage. |
| การสั่นสะเทือน | Unbalanced tires; driveshaft angle issues (less common with 1.5" lift). | Ensure tires are properly balanced; inspect driveshaft angles if vibrations persist (consult a specialist). |
7. ข้อมูลจำเพาะ
- แบบอย่าง: Belltech 152650BK
- ความสูงในการยก: Approximately 1.5 inches (Front and Rear)
- แอปพลิเคชัน: Ford Bronco Sport (2021+), Ford Bronco (2022+)
- ส่วนประกอบที่รวมอยู่: Front strut spacers, rear spacers, sway bar end links, mounting hardware.
- ประเภทการติดตั้ง: Direct bolt-in, no cutting or welding required.
- น้ำหนักสินค้า: ประมาณ 19.7 ปอนด์
- ขนาดสินค้า : 14.5 x 10.25 x 6.75 นิ้ว (บรรจุภัณฑ์)
- ยูพีซี: 722439008302
8. การรับประกันและการสนับสนุน
Belltech products are backed by a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the official Belltech webเว็บไซต์หรือติดต่อฝ่ายสนับสนุนลูกค้าโดยตรง
For technical assistance, installation questions, or to report missing/damaged parts, please visit the Belltech Store on Amazon or contact Belltech customer service through their official channels.
ผู้ผลิต: เบลท์เทค
หมายเลขรุ่นสินค้า: 152650BK
