Bewinner Night Vision Camera Module Board User Manual

1. บทนำ

This manual provides instructions for the Bewinner Night Vision Camera Module Board, designed for use with Raspberry Pi B 3/2. This 5-megapixel camera module features a fixed lens and connects via a 15 cm flat ribbon cable to the 15-pin MIPI Camera Serial Interface (CSI) connector on your Raspberry Pi. It supports image output up to 2592 x 1944 pixels.

2. ข้อมูลด้านความปลอดภัย

Handle the camera module with care to avoid damage to sensitive electronic components. Avoid exposing the module to static electricity, extreme temperatures, moisture, or direct sunlight. Disconnect power from your Raspberry Pi before connecting or disconnecting the camera module. Keep out of reach of children.

3. เนื้อหาบรรจุภัณฑ์

บรรจุภัณฑ์ควรมีรายการต่อไปนี้:

• 1 x Bewinner Night Vision Camera Module
• 1 x 15cm Flat Ribbon Cable
• 1 x ฝาครอบเลนส์

Image: Contents of the Bewinner Night Vision Camera Module package, including the camera board, ribbon cable, and a protective lens cap.

4. ข้อมูลจำเพาะ

Image: Detailed dimensions of the camera module, showing its compact size.

5. การตั้งค่าและการติดตั้ง

Follow these steps to connect the camera module to your Raspberry Pi:

1. Ensure your Raspberry Pi is powered off and disconnected from its power source.
2. Locate the CSI connector on your Raspberry Pi board. This is typically a long, narrow slot.
3. ค่อยๆ ดึงคลิปพลาสติกบนขั้วต่อ CSI ขึ้น
4. Insert the 15-pin flat ribbon cable from the camera module into the CSI connector. Ensure the silver contacts on the ribbon cable are facing the correct direction (usually towards the HDMI port on the Raspberry Pi, but refer to your Raspberry Pi's documentation for exact orientation).

ภาพ: จากบนลงล่าง view of the camera module's connector, showing the slot for the ribbon cable.

5. Push the plastic clip back down to secure the ribbon cable in place.
6. Connect the other end of the ribbon cable to the camera module's connector, ensuring proper orientation and secure connection.

Image: The camera module with the flat ribbon cable securely connected, ready for installation into a Raspberry Pi.

7. Once the camera module is securely connected, you can reconnect power to your Raspberry Pi.

6. คู่มือการใช้งาน

After physical installation, you will need to enable and configure the camera module through your Raspberry Pi's operating system (e.g., Raspberry Pi OS).

1. Boot your Raspberry Pi.
2. Open a terminal or access the desktop environment.
3. วิ่ง sudo raspi-config.
4. นำทางไปที่ ตัวเลือกอินเทอร์เฟซ > กล้อง and enable the camera module.
5. Reboot your Raspberry Pi when prompted.
6. To test the camera, you can use the raspistill command (for still images) or raspivid (for video) in the terminal. For example, to take a still image: raspistill -o image.jpg.
7. Refer to the official Raspberry Pi documentation for advanced camera usage and programming.

7. การบำรุงรักษา

Keep the camera lens clean using a soft, lint-free cloth. Avoid using abrasive materials or chemical cleaners. Store the module in a dry, dust-free environment when not in use. Do not attempt to disassemble the module, as this will void any potential warranty and may damage the components.

8 การแก้ไขปัญหา

• กล้องไม่ตรวจพบ:
  • Ensure the ribbon cable is correctly and securely inserted into both the camera module and the Raspberry Pi's CSI connector. Check the orientation of the cable.
  • Verify that the camera interface is enabled in raspi-config.
  • ตรวจสอบให้แน่ใจว่าระบบปฏิบัติการ Raspberry Pi ของคุณเป็นเวอร์ชันล่าสุด
• คุณภาพของภาพไม่ดี:
  • Check the lens for smudges or dust and clean gently.
  • Ensure adequate lighting for optimal performance, especially for night vision features.
  • Adjust camera settings (e.g., exposure, white balance) if using advanced software.
• โมดูลไม่เปิดใช้งาน:
  • Confirm the Raspberry Pi is receiving power.
  • Re-check all connections.

9. การรับประกันและการสนับสนุน

Specific warranty information for this Bewinner product is not provided in this manual. For warranty claims or technical support, please contact the retailer or manufacturer directly. Refer to the Bewinner official website or your purchase documentation for further details.