1. บทนำ
This manual provides detailed instructions for the safe and effective use of the Hakko FR-301 Portable Desoldering Tool. Please read this manual thoroughly before operating the tool and keep it for future reference. The Hakko FR-301 is a high-performance, self-contained desoldering tool designed for efficient removal of solder from printed circuit boards and electronic components.
An image showing the Hakko FR-301 Portable Desoldering Tool, a blue and yellow handheld device with a metal desoldering tip and a transparent solder collection chamber. The tool features a 'VACUUM' button on the handle and power settings indicated on the side.
2. ข้อมูลด้านความปลอดภัย
คำเตือน: การไม่ปฏิบัติตามคำแนะนำด้านความปลอดภัยเหล่านี้อาจทำให้เกิดไฟฟ้าช็อต ไฟไหม้ หรือบาดเจ็บสาหัสได้
- Always wear appropriate eye protection when operating the desoldering tool.
- Ensure the work area is well-ventilated to avoid inhaling solder fumes.
- Do not touch the desoldering tip or nozzle when the tool is hot. Allow it to cool completely before handling.
- เก็บเครื่องมือให้ห่างจากวัตถุไวไฟ
- Do not operate the tool with a damaged power cord or plug.
- Unplug the tool from the power outlet when not in use or before performing maintenance.
- This tool is for industrial use. Use only as intended.
3. การตั้งค่า
- การแกะกล่อง: Carefully remove all components from the packaging. Verify that all included components are present: the FR-301 unit, simple iron holder, carrying case, and various nozzles.
- การติดตั้งหัวฉีด: Select the appropriate nozzle for your application. Ensure the nozzle is clean and free of debris. Securely attach the nozzle to the heating element.
- การเชื่อมต่อไฟฟ้า: Connect the power cord to a suitable grounded electrical outlet. The tool operates on standard AC power.
- การจัดวาง: Place the desoldering tool in its simple iron holder when not actively in use to prevent accidental burns or damage.
4. คู่มือการใช้งาน
4.1 การเปิดเครื่องและการตั้งค่าอุณหภูมิ
- Plug the tool into a power outlet.
- Locate the power switch on the side of the handle. Switch it to the 'ON' position. The tool will begin to heat up.
- Adjust the temperature using the temperature control dial. The available temperature settings are:
- 1: 350℃ (660℉)
- 2: 380℃ (716℉)
- 3: 410℃ (770℉)
- 4: 440℃ (824℉)
- 5: 470℃ (878℉)
- Allow the tool to reach the set temperature before use. This usually takes a few minutes.
4.2 กระบวนการถอดบัดกรี
- Place the hot nozzle directly over the solder joint you wish to desolder, ensuring good contact.
- Allow the solder to melt.
- Press and hold the 'VACUUM' button located on the handle. The vacuum pump will activate, sucking the molten solder into the collection chamber.
- Once the solder is removed, release the 'VACUUM' button and lift the tool from the joint.
- Repeat the process for all necessary solder joints.
5. การบำรุงรักษา
5.1 การทำความสะอาดหัวฉีด
Regular cleaning of the nozzle is crucial for optimal performance.
- Ensure the tool is unplugged and completely cool.
- ถอดหัวฉีดออกจากเครื่องมือ
- Use a cleaning pin or brush to remove any accumulated solder or flux residue from the nozzle's interior and exterior.
- Reattach the clean nozzle securely.
5.2 Emptying the Solder Collection Chamber
The transparent collection chamber should be emptied regularly to maintain vacuum efficiency.
- Ensure the tool is unplugged and completely cool.
- Locate the collection chamber, typically a transparent tube near the front of the tool.
- Carefully detach the chamber according to the tool's design (refer to diagrams if available).
- Dispose of the collected solder safely.
- Clean the chamber and its filter (if applicable) with a suitable brush or compressed air.
- Reassemble the chamber securely.
5.3 การเปลี่ยนไส้กรอง
The internal filter prevents solder particles from entering the pump. Replace it periodically.
- Refer to the tool's specific design for filter access.
- Remove the old filter and replace it with a new, genuine Hakko replacement filter.
- Ensure the filter is correctly seated before reassembling the tool.
6 การแก้ไขปัญหา
| ปัญหา | สาเหตุที่เป็นไปได้ | สารละลาย |
|---|---|---|
| ไม่มีไฟฟ้า | Tool unplugged, power switch off, faulty outlet | Check power connection, turn on switch, test outlet |
| ดูดสูญญากาศไม่ดี | Clogged nozzle, full collection chamber, dirty filter, air leak | Clean nozzle, empty chamber, replace filter, check for loose connections |
| Tool not heating | Faulty heating element, incorrect temperature setting | Check temperature dial, contact support if element is faulty |
| Solder not melting | Insufficient temperature, poor contact with joint | Increase temperature, ensure full contact with solder joint |
7. ข้อมูลจำเพาะ
| คุณสมบัติ | รายละเอียด |
|---|---|
| หมายเลขรุ่น | FR-301 |
| ยี่ห้อ | ฮักโก |
| แหล่งพลังงาน | สายไฟ |
| วัดtage | 98 วัตต์ |
| น้ำหนักสินค้า | 3 ปอนด์ (1.36 กก.) |
| วัสดุ | Copper (for certain components) |
| ส่วนประกอบที่รวมอยู่ | Simple iron holder, carrying case, various nozzles |
| การใช้งานเฉพาะ | Industrial Use |
8. ข้อมูลการรับประกัน
The Hakko FR-301 Portable Desoldering Tool comes with a manufacturer's warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the warranty card included with your product or visit the official Hakko webเว็บไซต์.
9. การสนับสนุน
For technical assistance, replacement parts, or service inquiries regarding your Hakko FR-301, please contact Hakko customer support. Contact information can typically be found on the Hakko official website or on the product packaging. When contacting support, please have your product model number (FR-301) and purchase details ready.
แหล่งข้อมูลออนไลน์: Visit the official Hakko webเว็บไซต์ for additional resources, FAQs, and product updates.
