การแนะนำ
This manual provides detailed instructions for the installation, operation, and maintenance of the Trane KIT18110 OEM Upgraded Furnace Control Board Kit. This kit is designed as an American Standard / Trane OEM component for furnace units built after 1995. It includes the control board (CNT07541), ignitor, wire harness, and bracket.
หมายเหตุสำคัญ: For downflow units built in 1999 and earlier, use KIT18109. For all other units built after 1995, use KIT18110.
ข้อมูลด้านความปลอดภัย
คำเตือน: Installation and servicing of heating, ventilation, and air conditioning (HVAC) equipment can be hazardous due to system pressure, electrical components, and equipment location. Only trained and qualified service personnel should install, repair, or service HVAC equipment.
- Always disconnect all power to the furnace before installing or servicing the control board. Failure to do so can result in electrical shock, personal injury, or death.
- ตรวจสอบให้แน่ใจว่าเตาและอุปกรณ์ไฟฟ้าทั้งหมดต่อสายดินอย่างถูกต้อง
- สวมใส่อุปกรณ์ป้องกันส่วนบุคคล (PPE) ที่เหมาะสม รวมถึงแว่นตาและถุงมือเพื่อความปลอดภัย
- Verify all wiring connections are secure and correct according to the furnace manufacturer's specifications and local electrical codes.
- อย่าเลี่ยงอุปกรณ์ความปลอดภัยใดๆ
เนื้อหาแพ็คเกจ
The Trane KIT18110 kit typically includes the following components:
- Integrated Furnace Control Board (CNT07541)
- ignitor
- ลากสาย
- ตัวยึด
- คำแนะนำในการติดตั้ง
Image: The Trane KIT18110 furnace control board kit, showing the main circuit board, ignitor, and mounting hardware.
ความเข้ากันได้
This kit is an OEM replacement for various American Standard and Trane units built after 1995. It supersedes several older control board models. Always verify compatibility with your specific furnace model before installation.
Replaces / Supersedes Part Numbers:
- CNT-2854 / CNT02854
- CNT-3076 / CNT03076
- CNT-3798 / CNT03798
- CNT-5164 / CNT05164
- CNT-5165 / CNT05165
- CNT-5995 / CNT05995
- BAF00359 / BAF0359 / BAF-0359
- CNT05885 / CNT-5885
- CNT03604 / CNT-3604
- CNT07541 / CNT7541 / CNT-7541
- 50A65-475 / 50A65-475-07
- D341396P05 / D341396P03 / D341213P01 / D341396P01
- 50A65-120 / 50A65-143 / 50A65-288
- And many others.
Commonly Found in Models:
This kit is commonly found in the following A/TDX and A/TUX Gas Furnace Models:
- AUH1B040A9241AA, AUH1B040A9241AB
- AUH1B060A9361AA, AUH1B060A9361AB
- AUH1B080A9421AA, AUH1B080A9421BA, AUH1B080A9421BB
- AUH1C080A9601AA, AUH1C100A9481AA
- AUH1D100A9601AA, AUH1D120A9601AA
- TUH1B040A9241AA, TUH1B040A9241AB
- TUH1B060A9361AA, TUH1B060A9361AB
- TUH1B080A9421AA, TUH1B080A9421BA, TUH1B080A9421BB
- TUH1C080A9601AA, TUH1C100A9481AA
- TUH1D100A9601AA, TUH1D120A9601AA
Image: A stamp indicating "Trane OEM Component," signifying genuine parts.
การติดตั้ง / ตั้งค่า
This procedure is intended for qualified technicians. Refer to your furnace's specific service manual for detailed wiring diagrams and safety precautions.
- การตัดการเชื่อมต่อไฟฟ้า: Locate the main power switch for your furnace and turn it OFF. Additionally, turn off power at the circuit breaker or fuse box. Verify power is off using a voltagอี เมตร
- บอร์ดควบคุมการเข้าถึง: เปิดแผงควบคุมที่มีอยู่
- การเดินสายเอกสาร: Before disconnecting any wires, take clear photographs of all existing wiring connections to the old control board. Label wires if necessary to ensure correct re-connection.
- การตัดสายไฟ: ถอดสายไฟทั้งหมดออกจากแผงควบคุมเก่าอย่างระมัดระวัง
- ลบบอร์ดเก่า: Unscrew or unclip the old control board from its mounting location.
- ติดตั้งบอร์ดใหม่: Mount the new Trane KIT18110 control board using the provided bracket and screws. Ensure it is securely fastened.
- การเชื่อมต่อสายไฟ: Refer to your photographs and the wiring diagram in your furnace manual to connect all wires to the new control board. Pay close attention to terminal markings (e.g., R, W, Y, G, C).
- Install Ignitor: Replace the old ignitor with the new one provided in the kit, ensuring proper seating and connection to the control board via the wire harness.
- แผงการรักษาความปลอดภัย: Close and secure all furnace access panels.
- คืนค่าพลัง: Restore power to the furnace at the circuit breaker or fuse box, then turn on the main power switch for the furnace.
- การดำเนินการทดสอบ: Initiate a heating cycle to verify proper furnace operation, including ignition, fan operation, and temperature control. Observe for any error codes or unusual behavior.
การดำเนินการ
The Trane KIT18110 control board is an integrated furnace control that manages the sequence of operation for your furnace. Once correctly installed, it will automatically control the ignition, fan, and safety functions based on signals from the thermostat and internal sensors. No direct user interaction with the control board is required for normal operation.
Refer to your furnace's user manual for instructions on setting your thermostat and general furnace operation.
การซ่อมบำรุง
The control board itself typically requires no routine maintenance. However, regular maintenance of your furnace system is crucial for its longevity and efficient operation. This includes:
- การเปลี่ยนตัวกรอง: Replace or clean your furnace air filter regularly (monthly or as recommended by your furnace manufacturer).
- การตรวจสอบประจำปี: Schedule annual professional inspections and tune-ups for your furnace.
- ช่องระบายอากาศที่ชัดเจน: ตรวจสอบให้แน่ใจว่าช่องระบายอากาศเข้าและออกทั้งหมดไม่มีสิ่งกีดขวาง
- ทำความสะอาดหัวเตา: Keep burner areas clean and free of debris.
Always disconnect power before performing any maintenance on the furnace.
การแก้ไขปัญหา
The control board features diagnostic LED indicators that can help identify system faults. Consult your furnace's service manual for a detailed list of error codes and their meanings. Common issues and initial checks include:
- No Heat / No Power:
- Check if the furnace power switch is ON.
- Verify the circuit breaker for the furnace has not tripped.
- Ensure the thermostat is set to "Heat" and the temperature is above the ambient room temperature.
- Check for a blown fuse on the control board (if applicable).
- เตาไม่ติดไฟ:
- Check the ignitor for cracks or damage.
- ตรวจสอบให้แน่ใจว่าวาล์วจ่ายแก๊สเปิดอยู่
- ตรวจสอบว่าเซ็นเซอร์เปลวไฟสะอาดและอยู่ในตำแหน่งที่ถูกต้อง
- พัดลมไม่ทำงาน:
- Check if the thermostat fan setting is on "Auto" or "On".
- Ensure the air filter is not excessively dirty, restricting airflow.
- รหัสข้อผิดพลาด: Observe the diagnostic LED on the control board. Count the flashes or refer to the specific pattern to identify the fault code. Consult your furnace manual for the corresponding issue and recommended solution.
If you are unable to resolve an issue, contact a qualified HVAC technician.
ข้อมูลจำเพาะ
| หมายเลขรุ่นสินค้า | ชุด18110 |
| ผู้ผลิต | เทรน |
| ความเข้ากันได้ | American Standard / Trane units built after 1995 |
| ชุดประกอบด้วย | Control Board (CNT07541), Ignitor, Wire Harness, Bracket |
| ขนาดแพ็คเกจ | 12.09 x 7.2 x 5.08 นิ้ว |
| น้ำหนักสินค้า | 15.17 ออนซ์ |
ข้อมูลการรับประกัน
Specific warranty details for the Trane KIT18110 control board kit are typically provided by the point of purchase or Trane directly. It is recommended to retain your purchase receipt and consult the official Trane warranty documentation for your specific product. Generally, OEM parts carry a limited warranty against manufacturing defects.
สนับสนุน
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact your authorized Trane dealer or a qualified HVAC service professional. You may also visit the official Trane webเว็บไซต์สำหรับแหล่งข้อมูลเพิ่มเติมและข้อมูลการติดต่อ
