คู่มือผู้ใช้ไฟเตือนแฟลช LED 4 ดวง Maxxima M20384WYCL สีขาว/สีเหลืองอำพันแบบบางพิเศษ

1. สินค้าหมดview

The Maxxima M20384WYCL is an ultra-thin profile 4 LED warning light designed for surface mounting. This model features 2 white LEDs and 2 amber LEDs with a clear lens, providing strong light output for emergency, warning, and safety applications. Its low-profile design allows for easier mounting and a slimmer appearance.

ภาพที่ 1.1: ด้านหน้า view of the Maxxima M20384WYCL White/Amber Ultra Thin 4 LED Warning Strobe Light.

2. อะไรอยู่ในกล่อง

ตรวจสอบว่าส่วนประกอบทั้งหมดมีอยู่ก่อนเริ่มการติดตั้ง

• Maxxima M20384WYCL Warning Strobe Light
• ปะเก็น
• Snap-On Black Bezel
• สกรูยึด

3. การตั้งค่าและการติดตั้ง

This warning light is designed for surface mount installation. Ensure the mounting surface is clean, flat, and provides adequate space for the light and wiring.

3.1 การติดตั้ง

1. Select a suitable mounting location on your vehicle. The light's dimensions are approximately 4.4 inches (L) x 0.9 inches (D) x 1.5 inches (H).
2. Position the light with the included gasket and black bezel. Mark the drilling points for the mounting screws.
3. เจาะรูนักบินในตำแหน่งที่ทำเครื่องหมายไว้
4. Secure the light to the surface using the provided mounting screws. Ensure a tight fit to prevent moisture ingress.

Optional mounting accessories are available and sold separately, including Maxxima Part# M50144 for grommet mounting, M50138 for a chrome bezel, or M50115 for a stainless steel bracket.

ภาพที่ 3.1: ด้านข้างfile of the warning light, highlighting its ultra-thin design.

ภาพที่ 3.2: อดีตample installation of the warning light on a vehicle grille.

3.2 การเดินสายไฟ

The M20384WYCL light features 4 blunt cut leads for electrical connection. Ensure all connections are secure and properly insulated to prevent short circuits and corrosion.

ภาพที่ 3.3: ด้านหลัง view of the light with wiring leads.

Typical Wiring Configuration:

• สายสีแดง: Positive (+) power input (12.8 VDC). Connect to a fused power source.
• สายสีดำ: Negative (-) ground. Connect to a chassis ground.
• สายสีเหลือง: Pattern selection. Momentarily touch this wire to the black (ground) wire to cycle through the 22 available flash patterns.
• ลวดขาว: Synchronization. Connect the white wires of multiple lights together for synchronized or alternating flashing. Refer to the specific wiring diagram for your desired synchronization mode (not provided in general product data).

ควรตัดกระแสไฟก่อนทำการเชื่อมต่ออุปกรณ์ไฟฟ้าทุกครั้ง

4. คู่มือการใช้งาน

The Maxxima M20384WYCL warning light offers 22 selectable flash patterns and is capable of both synchronized and alternating flashing.

4.1 การเปิด/ปิดเครื่อง

Once properly wired, the light will activate when power is supplied to the red wire. To turn the light off, remove power from the red wire.

4.2 Changing Flash Patterns

With the light powered on, momentarily touch the yellow wire to the black (ground) wire. Each momentary touch will advance the light to the next flash pattern in its sequence. Cycle through the patterns until the desired one is selected.

4.3 การซิงโครไนซ์

For synchronized or alternating flashing with multiple M20384WYCL lights, connect the white wires of all lights together. The specific synchronization behavior (e.g., all flash together, or alternate) is typically determined by the selected flash pattern and the wiring configuration (refer to a detailed wiring diagram if available from the manufacturer for specific synchronization modes).

Image 4.1: Key features of the warning light.

5. การบำรุงรักษา

The Maxxima M20384WYCL warning light is designed for durability and minimal maintenance.

• การทำความสะอาด: Clean the lens periodically with a soft cloth and mild soap and water. Avoid abrasive cleaners or solvents that could damage the polycarbonate lens.
• การตรวจสอบ: Regularly inspect the wiring for any signs of wear, damage, or corrosion. Ensure mounting screws remain tight.
• ความทนทาน: The unit features a polycarbonate lens and housing, and completely resin-sealed electronics, providing protection against environmental elements.

6 การแก้ไขปัญหา

If you encounter issues with your Maxxima M20384WYCL warning light, consider the following:

• แสงไม่สามารถส่องสว่างได้:
  • Check all electrical connections (red wire to positive, black wire to ground).
  • Verify that the power source is active and providing 12.8 VDC.
  • Check for any blown fuses in the power circuit.
• Light flashes erratically or not as expected:
  • Ensure the yellow pattern selection wire is not continuously grounded, which could interfere with pattern selection.
  • If multiple lights are synchronized, check the white wire connections for continuity and proper isolation from ground.
• Moisture inside the lens: While the unit is resin-sealed, extreme conditions or improper installation can sometimes lead to condensation. If persistent, contact Maxxima support.

If troubleshooting steps do not resolve the issue, refer to the warranty information for further assistance.

7. ข้อมูลจำเพาะ

Image 7.1: Visual representation of product specifications.

8. ข้อมูลการรับประกัน

The Maxxima M20384WYCL Warning Strobe Light is backed by a 5 Year Maxxima Warranty. This warranty covers defects in materials and workmanship under normal use. For warranty claims or detailed terms and conditions, please contact Maxxima customer support.

9. การสนับสนุน

For technical assistance, product inquiries, or warranty support, please visit the official Maxxima webหรือติดต่อฝ่ายบริการลูกค้า คุณยังสามารถเยี่ยมชม ร้าน Maxxima บน Amazon สำหรับข้อมูลผลิตภัณฑ์และทรัพยากรเพิ่มเติม