LAUNCH CNC602A Injector Cleaner and Tester User Manual

1. บทนำ

The LAUNCH CNC602A Injector Cleaner and Tester is a professional automotive tool designed for comprehensive maintenance of fuel injectors. It performs simultaneous cleaning and testing of multiple injectors, ensuring optimal engine performance and fuel efficiency. This manual provides detailed instructions for safe and effective operation of the device.

2. ข้อมูลด้านความปลอดภัย

• ควรใช้งานเครื่องในบริเวณที่มีอากาศถ่ายเทได้ดีเสมอ
• Do not smoke or use open flames near the cleaning or testing fluids.
• สวมอุปกรณ์ป้องกันส่วนบุคคลที่เหมาะสม รวมถึงแว่นตานิรภัยและถุงมือ
• Ensure the unit is properly grounded before operation.
• Use only recommended cleaning and testing fluids.
• Do not place anything on the control panel that could interfere with operation or cause damage.
• In case of a damaged power supply or short circuit, discontinue use immediately.

3. ส่วนประกอบของผลิตภัณฑ์และสิ่งของในบรรจุภัณฑ์

The LAUNCH CNC602A comes with a comprehensive set of accessories to facilitate various cleaning and testing procedures.

ภาพ: Various accessories and cables included with the LAUNCH CNC602A Injector Cleaner and Tester.

รายการแพ็กเกจ:

• 105020217 CNC pulse signal connection cable 1, T=0.5
• 105020218 CNC pulse signal connection cable 2, T=0.8
• 103260037 Ultrasonic cleaner assembly 100W
• 106030038 On-vehicle adaptor package (tool kits)
• 107010428 CNC-602A user manual (En&Ch)
• 103250013 Top-supply connector 1
• 103250015 Swiss thread adaptor for fuel top-supply injector
• 103250016 Coarse thread adaptor for fuel top-supply injector
• 103250018 CNC-601/801 Hexangular stopper
• 104990012 CNC-801 BUICK injector adaptor
• 199010019 Injector testing liquid (pick out)
• 307030024 Injector detergent (pick out)

4. การตั้งค่า

Before operating the unit, ensure it is placed on a stable, level surface and connected to a suitable power supply (AC110V±10%, 50/60Hz).

ภาพ: Power switch and socket for connecting the unit to a 110V AC power supply.

ขั้นตอนเริ่มต้น:

1. เชื่อมต่อพลังงาน: Plug the unit into a grounded AC110V power outlet.
2. ติดตั้งวาล์วระบายน้ำ: Attach the cleaning/testing agent discharge valve to the designated port.
3. Prepare Ultrasonic Bath: Place the ultrasonic cleaning assembly into its designated slot.
4. Install Signal Wires: Connect the pulse signal connection cables to the unit.

5. คู่มือการใช้งาน

The CNC602A offers both ultrasonic cleaning and various testing functions for fuel injectors.

ภาพ: The control panel with function selection, pulse width adjustment, and pressure controls.

5.1. ขั้นตอนการทำความสะอาดด้วยคลื่นอัลตราโซนิค

1. Pre-clean Injectors: Clean the injector's exterior with gasoline or a suitable cleaning liquid before placing them in the unit.
2. Place Injectors: Position the injectors in the ultrasonic bathtub.
3. Add Cleaning Fluid: Pour cleaning fluid into the ultrasonic bathtub, ensuring injectors are submerged.
4. Connect Pulse Signals: Attach the pulse signal cables to the injectors.
5. Activate Ultrasonic System: Turn on the ultrasonic system. The pulsed energy, combined with the cleaning fluid, will dislodge carbon and impurities from inside the injectors.
6. Heat Mode (Optional): If desired, activate the heating mode for enhanced cleaning.

ภาพ: Injectors undergoing ultrasonic cleaning in the dedicated bath.

5.2. ขั้นตอนการทดสอบหัวฉีดน้ำมันเชื้อเพลิง

1. หัวฉีดแบบติดตั้ง: Secure the cleaned injectors onto the main machine's test bench.
2. เติมของเหลวทดสอบ: Pour the dedicated testing fluid into the fuel tank (4700ml capacity). Ensure the fluid level is within the specified range.
3. Connect Power and Signal: Ensure all injectors are correctly connected for power and pulse signals.
4. Select Test Function: Use the control panel to select the desired test function (e.g., Idle Speed Test, Leakage Test, Sprayability Test).
5. ปรับพารามิเตอร์: Set simulated RPM, time, and pulse width as required for the selected test.
6. เริ่มการทดสอบ: Initiate the test and observe injector performance in the graduated cylinders.
7. ปรับแรงดัน: Use the pressure adjustment knob to modify system pressure during testing as needed.

Available Testing Functions:

• การทำความสะอาดด้วยคลื่นเสียงความถี่สูง: Removes carbon deposits and impurities using ultrasonic vibration.
• Idle Speed Test (0-20ms): Simulates engine idling speed to test injector state.
• Medium Speed Test (0-7.5ms): Simulates medium engine speed to test injector state.
• High-Speed Test (0-4ms): Simulates high engine speed to test injector state.
• การทดสอบอัตราเร่ง: Simulates vehicle acceleration to test injector performance.
• Shift Speed Test: Simulates vehicle shifting state to test injector working performance.
• การทดสอบการรั่วไหล: Checks the sealing condition of the fuel injector.
• Idle Speed Sprayability Test: Tests spray performance at engine idling state.
• Medium Speed Sprayability Test: Tests spray performance at medium engine speed.
• High-Speed Sprayability Test: Tests spray performance at high engine speed.
• Reverse Flush: Cleans injectors by flowing test liquid from outlet to inlet, removing internal dirt or strainers (for top fuel supply injectors).
• No-Disassembly Cleaning: Direct cleaning without disassembling injectors (requires special adapters).

6. การบำรุงรักษา

Regular maintenance ensures the longevity and accuracy of your LAUNCH CNC602A unit.

1. การจัดการของเหลว: After each use, drain all cleaning and testing fluids from the unit. Store fluids properly according to their safety data sheets.
2. หน่วยทำความสะอาด: เช็ดภายนอกเครื่องด้วยผ้านุ่มๆamp cloth. Avoid using harsh chemicals that may damage the surface or internal components.
3. ตรวจสอบส่วนประกอบ: Regularly check all hoses, connections, and adapters for wear, damage, or leaks. Replace any damaged parts immediately.
4. พื้นที่จัดเก็บ: Store the unit in a clean, dry environment away from direct sunlight and extreme temperatures.

ภาพ: Fuel intake port and warning label, emphasizing proper fluid handling.

7 การแก้ไขปัญหา

หัวข้อนี้จะกล่าวถึงปัญหาทั่วไปที่คุณอาจพบระหว่างการใช้งาน

• เครื่องไม่เปิดเครื่อง: Check power cable connection and ensure the power switch is in the 'ON' position. Verify the power outlet is functional.
• No ultrasonic cleaning action: Ensure the ultrasonic cleaning function is selected and the cleaning fluid level is adequate. Check connections to injectors.
• Inconsistent spray pattern/flow: Verify that injectors are clean and free of blockages. Check for proper seating of injectors and adapters. Ensure correct pressure settings.
• การรั่วไหลของของไหล: Inspect all connections, hoses, and O-rings for proper sealing. Tighten any loose fittings.
• Pressure gauge not responding: Check the oil supply hose connection and ensure the pressure adjustment knob is functioning correctly.

8. ข้อมูลจำเพาะ

9. การรับประกันและการสนับสนุน

The LAUNCH CNC602A Injector Cleaner and Tester comes with a รับประกัน 1 ปี for damages caused by non-human factors. For any needs or support, please contact customer service. We aim to respond within 24 hours.