Kidde Smoke Detector i9050 Instruction Manual

สินค้าเกินview

The Kidde Smoke Detector, model i9050, is designed to provide early warning of fire by detecting smoke. This ionization smoke alarm is battery-operated, ensuring continuous protection even during power outages. It is equipped with an 85-decibel alarm and visual indicators for power and smoke detection.

• Basic Ionization Smoke Alarm: Detects invisible fire particles associated with flaming fires.
• ใช้พลังงานจากแบตเตอรี่: Operates on a 9V battery (included), providing protection during power failures.
• ติดตั้งง่าย: No wiring required for setup.
• ไฟ LED แสดงสถานะ: A solid green LED indicates power, and a red LED indicates smoke or fire detection.
• ปุ่มทดสอบการปิดเสียง: Allows for testing the alarm and temporarily silencing nuisance alarms.
• คำเตือนแบตเตอรี่ต่ำ: The unit will chirp when the battery needs replacement.
• ใบรับรอง: UL จดทะเบียน

ด้านหน้า view of the Kidde Smoke Detector i9050, showing the test/hush button and alarm grille.

การติดตั้งและการตั้งค่า

1. การเลือกสถานที่

For optimal safety, install smoke detectors on every level of your home, inside each bedroom, and in the hallway outside of sleeping areas. Avoid placing detectors in kitchens, bathrooms, or garages where cooking fumes, steam, or vehicle exhaust could cause nuisance alarms.

Diagram illustrating recommended placement of smoke alarms, carbon monoxide alarms, fire extinguishers, and escape ladders within a typical home layout. Smoke alarms are recommended in bedrooms, hallways, living rooms, and basements.

2. การติดตั้งแบตเตอรี่

The Kidde i9050 smoke detector operates on a single 9-volt battery, which is included. Ensure the battery is properly inserted before mounting the unit.

1. Twist the alarm counter-clockwise from the mounting bracket to remove it.
2. Open the battery compartment door located on the back of the alarm.
3. Connect the 9-volt battery to the battery clip, ensuring correct polarity (+ to + and - to -).
4. Place the battery into the compartment and close the door securely.
5. The alarm may chirp briefly upon battery insertion, indicating it is receiving power.

Image showing the Kidde smoke detector with its battery compartment open, revealing the 9V battery and connection points. This highlights the battery-operated nature of the device.

3 การติดตั้งระบบเตือนภัย

The alarm comes with a mounting bracket for easy installation on a wall or ceiling. No complex wiring is required.

1. Select a suitable mounting location, ensuring it is away from air vents, windows, or doors that could interfere with smoke detection.
2. Hold the mounting bracket against the wall or ceiling at your chosen location and mark the two mounting holes.
3. Drill two holes at the marked spots. Insert the plastic anchor plugs (if needed for drywall) into the drilled holes.
4. ติดขายึดโดยใช้สกรูที่ให้มา
5. Align the alarm with the mounting bracket and twist it clockwise until it locks securely into place.

A woman is shown easily installing the Kidde smoke detector on a ceiling, demonstrating the simple, tool-free attachment process after the mounting bracket is in place.

คำแนะนำการใช้งาน

การทำงานปกติ

Once installed with a fresh battery, the smoke detector is continuously monitoring for smoke. A solid green LED light indicates that the alarm is receiving power and functioning correctly.

The Kidde smoke detector with its green LED illuminated, indicating that the unit is powered and operating normally.

สภาพสัญญาณเตือน

If smoke or fire is detected, the alarm will sound a loud 85-decibel horn, and a red LED light will flash rapidly. This indicates an emergency and requires immediate attention.

ปุ่มทดสอบ/ปิดเสียง

The large button on the front of the alarm serves two functions:

• การทดสอบ: Press and hold the button to test the alarm's electronic circuitry, horn, and battery functions. The alarm should sound loudly. Release the button to stop the test. This should be done weekly.
• Hushing Nuisance Alarms: If the alarm sounds due to cooking fumes or shower steam, press the button to temporarily silence the alarm for approximately 10 minutes. The red LED will flash every 10 seconds during the hush period. The alarm will automatically reset after this period if the smoke condition has cleared.

Image showing the Kidde smoke detector with its dimensions (5" diameter, 1.75" depth) and the prominent test button, emphasizing its function to verify battery and alarm operation.

การซ่อมบำรุง

การทดสอบรายสัปดาห์

It is crucial to test your smoke alarm weekly to ensure it is functioning correctly. Press and hold the Test/Hush button until the alarm sounds. If the alarm does not sound, replace the battery immediately or consult the troubleshooting section.

การเปลี่ยนแบตเตอรี่

The smoke detector will emit a short chirp approximately once every minute when the 9-volt battery is low and needs to be replaced. Replace the battery immediately upon hearing this chirp.

1. Twist the alarm counter-clockwise from the mounting bracket to remove it.
2. เปิดประตูช่องใส่แบตเตอรี่
3. Disconnect the old 9-volt battery from the clip and dispose of it properly.
4. Connect a new 9-volt battery (e.g., Eveready or Duracell recommended) to the battery clip, ensuring correct polarity.
5. Place the new battery into the compartment and close the door securely.
6. Re-attach the alarm to the mounting bracket by twisting it clockwise until it locks.
7. Test the alarm using the Test/Hush button to confirm proper operation.

The back of the Kidde smoke detector, showing the battery compartment and instructions to refer to the owner's manual for complete operating instructions. It also indicates the model number and UL listing.

การทำความสะอาดเครื่องตรวจจับควัน

Dust and debris can accumulate on the smoke alarm and affect its performance. It is recommended to clean your smoke alarm at least once a month.

• ถอดสัญญาณเตือนภัยออกจากแท่นยึด
• Use a soft brush attachment on your vacuum cleaner to gently vacuum around the alarm's vents and openings.
• Do not paint the alarm, as paint can clog the sensing chambers and prevent proper operation.
• Re-attach the alarm to the mounting bracket after cleaning.

การแก้ไขปัญหา

สำหรับการแก้ไขปัญหาโดยละเอียดเพิ่มเติม โปรดดูที่เว็บไซต์อย่างเป็นทางการ คู่มือการแก้ไขปัญหา (PDF).

ข้อมูลจำเพาะ

• หมายเลขรุ่น: ไอ9050
• แหล่งพลังงาน: 9-Volt Battery (included)
• ประเภทเซนเซอร์: การแตกตัวเป็นไอออน
• ระดับความดังของเสียงเตือน: 85 เดซิเบลที่ระยะ 10 ฟุต
• ขนาดสินค้า : ลึก 1.75 นิ้ว x กว้าง 5 นิ้ว x สูง 5 นิ้ว
• น้ำหนักสินค้า: 6.4 ออนซ์
• สี: สีขาว
• ความชื้นในการทำงาน: ความชื้นสัมพัทธ์สูงถึง 85% ไม่มีการควบแน่น
• คะแนนอุณหภูมิด้านบน: 38 องศาเซลเซียส
• ผู้ผลิต: Kidde Safety
• ใบรับรอง: ได้รับการรับรองจาก UL

การรับประกันและการสนับสนุน

การรับประกันแบบจำกัด

The Kidde Smoke Detector i9050 comes with a 10-year limited manufacturer's warranty. This warranty period begins when the alarm is powered on. If the power-on date is unknown, it should be assumed that the alarm needs to be replaced after 10 years from the manufacturing date.

ความช่วยเหลือเพิ่มเติม

For comprehensive operating instructions, detailed safety information, or any further assistance, please refer to the official user guides:

• คู่มือผู้ใช้ (PDF)
• คู่มือการใช้งาน (PDF)

คุณยังสามารถเยี่ยมชม Kidde Store on Amazon สำหรับข้อมูลผลิตภัณฑ์และทรัพยากรเพิ่มเติม