Frigidaire 318293820 Surface Element Switch Instruction Manual

1. บทนำ

This manual provides detailed instructions for the installation, operation, and maintenance of the Frigidaire 318293820 Surface Element Switch. This component is a genuine replacement part designed to control the heat output of a surface burner on compatible Frigidaire electric ranges. Proper installation and handling are crucial for safe and effective operation.

รูปที่ 1 : ด้านหน้า view of the Frigidaire 318293820 Surface Element Switch.

2. ข้อมูลด้านความปลอดภัย

คำเตือน: Before attempting any installation, maintenance, or repair, ensure the appliance is completely disconnected from its power source. Failure to do so may result in electric shock, personal injury, or death. Always wear appropriate personal protective equipment, such as gloves and safety glasses.

• Disconnect power to the range at the circuit breaker or fuse box before beginning.
• If the range is hard-wired, ensure the main power supply to the house is turned off.
• ควรใช้งานชิ้นส่วนอิเล็กทรอนิกส์ด้วยความระมัดระวังเพื่อป้องกันความเสียหาย
• ให้แน่ใจว่าการเชื่อมต่อทั้งหมดแน่นหนาดีก่อนจะคืนพลังงาน
• หากคุณไม่แน่ใจเกี่ยวกับขั้นตอนใด ๆ โปรดปรึกษาช่างเทคนิคเครื่องใช้ไฟฟ้าที่มีคุณสมบัติเหมาะสม

3. การตั้งค่าและการติดตั้ง

This section outlines the general procedure for replacing a surface element switch. Specific steps may vary slightly depending on your range model.

3.1 เครื่องมือที่จำเป็น

• Number 1 Square Head Screwdriver
• คีมปากแหลม

3.2 ขั้นตอนการติดตั้ง

1. ตัดการเชื่อมต่อไฟฟ้า: Ensure the range is completely disconnected from its power source. Pull the range away from the wall to access the rear.
2. Remove Back Panel: Using a Number 1 square head screwdriver, remove the screws securing the upper back panel of the range. Typically, there are three screws across the bottom and one in the center at the top. Carefully remove the panel and set it aside.
3. ค้นหาสวิตช์: Identify the surface element switch that needs replacement. It will be connected to several wires.
4. การเดินสายเอกสาร: Before disconnecting any wires, carefully note the position and color of each wire connected to the old switch. Taking a photograph is highly recommended to ensure correct reassembly.
5. Remove Wires: Using needle-nose pliers, carefully disconnect each wire from the terminals of the old switch. The wires may be tightly secured.
6. ถอดสวิตช์เก่าออก: Unscrew the mounting screws that secure the switch to the control panel. Remove the old switch.
7. ติดตั้งสวิตช์ใหม่: Position the new Frigidaire 318293820 Surface Element Switch in place and secure it with the mounting screws.
8. เชื่อมต่อสายไฟ: Reconnect the wires to the new switch's terminals according to your documentation from Step 4. Ensure all connections are firm and secure.
9. Reattach Back Panel: Place the back panel back onto the range and secure it with the screws removed in Step 2.
10. คืนค่าพลัง: Push the range back into its original position and reconnect the power supply.

3.3 Visual Guide: Installation Video

Video 1: Installation guide for a similar infinite range switch. While the model number in the video may differ slightly, the general installation steps are applicable.

3.4 ขนาดสินค้า

Figure 2: Approximate dimensions of the surface element switch.

4. คู่มือการใช้งาน

The Frigidaire 318293820 Surface Element Switch functions as a control for your range's surface burner. Once installed, its operation is integrated with your appliance's control panel.

• Turn the corresponding control knob to the desired heat setting (e.g., Low, Medium, High).
• The switch regulates the power supplied to the surface element, allowing for precise temperature control.
• Turn the knob to the 'OFF' position to deactivate the burner.

5. การบำรุงรักษา

The surface element switch is a sealed unit and generally requires no internal maintenance. However, regular external care of your range's control panel is recommended.

• Keep the control panel area clean and free from food debris or spills.
• ใช้แบบนุ่มๆamp cloth to wipe the control panel. Avoid abrasive cleaners or harsh chemicals that could damage the finish or markings.
• Ensure control knobs are properly seated and not loose.

6 การแก้ไขปัญหา

If you experience issues with your surface element after replacing the switch, consider the following:

• องค์ประกอบไม่ร้อน: Check all wire connections to ensure they are secure. Verify that the correct element is selected and the control knob is turned to an 'ON' position. Ensure power is supplied to the range.
• Element Stuck On/Constant Heat: This could indicate a faulty switch or incorrect wiring. Immediately disconnect power to the range and re-check wiring against your documentation. If the issue persists, the switch may be defective.
• No Power to Range: ตรวจสอบเบรกเกอร์หรือกล่องฟิวส์ว่ามีเบรกเกอร์ตัดวงจรหรือฟิวส์ขาดหรือไม่

หากขั้นตอนการแก้ไขปัญหาไม่สามารถแก้ไขปัญหาได้ ขอแนะนำให้ติดต่อช่างซ่อมเครื่องใช้ไฟฟ้าที่มีคุณสมบัติเหมาะสม

7. ข้อมูลจำเพาะ

8. ข้อมูลการรับประกัน

As a genuine Frigidaire replacement part, this surface element switch is typically covered by the manufacturer's standard warranty for replacement parts. Please refer to your original appliance's warranty documentation or contact Frigidaire customer service for specific warranty terms and conditions. Keep your proof of purchase for any warranty claims.

9. การสนับสนุน

For further assistance, technical support, or to purchase additional genuine Frigidaire parts, please visit the official Frigidaire website or contact their customer service department. You can also visit the Frigidaire Store on Amazon for more products and information.

Visit the Frigidaire Store on Amazon