คู่มือการใช้งาน+

ไวเปอร์ 7145V

Viper 7145V Remote Replacement User Manual

For Viper Security and Remote Start Systems

การแนะนำ

This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your Viper 7145V 4-button 1-way remote replacement. This remote is designed to function with compatible Viper security and remote start systems, offering convenient control over your vehicle's security features.

The Viper 7145V remote offers a range of up to 1/4 mile (approximately 400 meters) for reliable communication with your vehicle's system.

สินค้าเกินview

Viper 7145V 4-button remote control with lock, unlock, AUX, and asterisk buttons

Figure 1: Viper 7145V 4-Button Remote Control. Features a black casing with a blue LED indicator, a lock button, an unlock button, an AUX button, and an orange asterisk button, along with a metal keyring attachment.

The Viper 7145V is a compact, ergonomic 4-button remote control. It is a direct replacement or additional remote for several Viper security and remote start systems.

คุณสมบัติหลัก:

ความเข้ากันได้ของระบบ:

This remote is compatible with the following Viper system models:

บันทึก: Always verify your existing system's model number to ensure full compatibility.

การตั้งค่าและการเขียนโปรแกรม

To program your new Viper 7145V remote, you will need access to your vehicle's Valet button. The Valet button is typically located near the alarm's control module, under the dashboard, or in the fuse box area. Consult your vehicle's alarm installation manual or a qualified installer if you cannot locate it.

ขั้นตอนการเขียนโปรแกรม:

  1. Ensure all vehicle doors are closed and the ignition key is removed.
  2. Open the driver's side door.
  3. Insert the ignition key and turn it to the "ACC" or "ON" position.
  4. Press and release the Valet button once. Then, immediately press and ถือ the Valet button.
  5. The system will emit a chirp or honk, indicating it is in programming mode.
  6. While still holding the Valet button, press the ล็อค button on your new 7145V remote. The system will chirp once to confirm the remote has been learned for Channel 1 (typically Lock/Unlock).
  7. Release the Valet button.
  8. To program additional functions (e.g., AUX, Panic), repeat steps 3-4, but for step 4, press and release the Valet button the corresponding number of times for the desired channel before holding it down. For example, for Channel 2, press and release Valet twice, then hold.
  9. Once the system chirps to indicate the channel, press the corresponding button on your remote (e.g., AUX for Channel 2, Asterisk for Channel 3).
  10. After programming all desired buttons, turn the ignition key to the "OFF" position to exit programming mode. The system will chirp to confirm exit.

หมายเหตุสำคัญ: Some systems may require pressing the Valet button 7 times and holding on the 8th press to enter programming mode for certain channels. If the standard method does not work, consult your specific Viper system's manual or a professional installer.

คำแนะนำการใช้งาน

The Viper 7145V remote provides control over your vehicle's security and remote start functions. The primary functions are typically assigned as follows:

For remote start functionality, typically a combination of button presses (e.g., pressing the Lock button twice) is required. Consult your specific Viper system's manual for remote start activation procedures.

การซ่อมบำรุง

การเปลี่ยนแบตเตอรี่:

The Viper 7145V remote requires แบตเตอรี่ AAA 1 ก้อน for operation. When the remote's range decreases or it becomes unresponsive, it is likely time to replace the battery.

  1. ค้นหาฝาครอบช่องใส่แบตเตอรี่ที่ด้านหลังของรีโมต
  2. Using a small flat-head screwdriver or a coin, gently pry open the battery cover.
  3. Remove the old AAA battery, noting its orientation (+/-).
  4. Insert a new AAA battery, ensuring correct polarity.
  5. Snap the battery cover back into place until it is securely closed.
  6. ทดสอบการทำงานของรีโมทคอนโทรล

คำเตือน: ทิ้งแบตเตอรี่เก่าด้วยความรับผิดชอบตามข้อบังคับท้องถิ่น

การแก้ไขปัญหา

ปัญหาสาเหตุที่เป็นไปได้สารละลาย
Remote does not respond or has reduced range.Low or dead battery. Out of range. Remote not programmed correctly.Replace the AAA battery. Move closer to the vehicle. Re-program the remote following the "Setup and Programming" section.
Unlock button does not work, but Lock button works for both.System configuration or remote design variation.This is normal for some Viper systems and 7145V remotes. Use the Lock button for both locking and unlocking. No action required.
Remote does not program to the system.Incorrect programming steps. Valet button not located or faulty. Incompatible system.Review "Setup and Programming" steps carefully. Ensure the Valet button is functioning. Confirm your Viper system is listed under "System Compatibility". Seek professional assistance if issues persist.
Remote functions are incorrect (e.g., AUX button activates panic).Buttons programmed to wrong channels.Re-program the remote, paying close attention to which button is pressed for each programming channel.

ข้อมูลจำเพาะ

การรับประกันและการสนับสนุน

For warranty information and technical support, please refer to the documentation provided with your original Viper security or remote start system, or visit the official Viper webไซต์นี้ โปรดเก็บหลักฐานการซื้อไว้เพื่อใช้ยืนยันการรับประกัน

For further assistance, you may contact Viper customer support or consult a certified Viper installer.

ไวเปอร์ อย่างเป็นทางการ Webเว็บไซต์: www.viper.com