คู่มือการใช้งานไส้กรองน้ำมันเครื่อง Nissan PITWORK รุ่น AY100-NS004

1. บทนำ

This instruction manual provides essential information for the proper installation, maintenance, and understanding of the Nissan PITWORK Oil Filter AY100-NS004. Designed as a genuine replacement part, this oil filter is crucial for maintaining engine health by effectively removing contaminants from your engine oil. Please read this manual thoroughly before installation and operation to ensure optimal performance and safety.

2. สินค้าหมดview

The Nissan PITWORK Oil Filter AY100-NS004 is engineered to meet the high standards of Nissan vehicles. It features a durable housing and advanced filtration media to protect your engine from harmful particles. Regular replacement of the oil filter is vital for the longevity and efficiency of your vehicle's engine.

3. ข้อมูลด้านความปลอดภัย

Please observe the following safety precautions during installation and maintenance:

• เสี่ยงต่อการไหม้: Perform work only after the engine has completely cooled down to avoid severe burns from hot engine components or oil.
• การรั่วไหลของน้ำมัน: Improper installation or damaged seals can lead to oil leaks, which may cause engine seizure or fire hazards. Ensure all steps are followed carefully.

4. คำแนะนำในการติดตั้ง

Follow these steps for proper installation of the Nissan PITWORK Oil Filter AY100-NS004:

1. ตรวจสอบความเข้ากันได้: Confirm that the replacement filter matches your vehicle's specific model, type, and part number. Refer to your vehicle's owner's manual or the compatibility chart in this manual.
2. Prepare Sealing Surface: Thoroughly wipe off any dirt, debris, or foreign matter from the engine-side sealing surface where the filter will attach. A clean surface is critical for a proper seal.
3. Lubricate Gasket: Ensure the new filter's rubber gasket is correctly seated in its groove. Then, apply a thin layer of clean engine oil around the entire circumference of the gasket. This helps create a good seal and prevents damage during tightening.
4. ติดตั้งตัวกรอง: Screw the filter onto the engine by turning it clockwise. Hand-tighten until the gasket makes firm contact with the engine-side sealing surface. Once contact is made, use a suitable filter wrench to tighten the filter according to the rotation specified on the filter body. อย่าขันแน่นจนเกินไป
5. Check for Leaks and Oil Level: After installation, add the appropriate amount of new engine oil. Start the engine and let it run for at least 3 minutes. Then, turn off the engine, wait a few minutes for the oil to settle, and check for any oil leaks around the filter's seal. Finally, confirm the engine oil level using the dipstick and add more oil if necessary.

5. การบำรุงรักษา

For optimal engine performance and longevity, adhere to your vehicle's recommended maintenance schedule:

• ระดับน้ำมัน: Regularly check your engine oil level and maintain it within the recommended range as specified in your vehicle's owner's manual.
• Replacement Timing: The timing for oil filter replacement should strictly follow the guidelines provided in your vehicle's 'Maintenance Handbook' or 'Owner's Manual'. This typically coincides with engine oil changes.

6. ข้อมูลจำเพาะ

7. ความเข้ากันได้

The PITWORK Oil Filter AY100-NS004 is compatible with various Nissan and Mazda vehicle models. Please verify your vehicle's specific model and engine type against the list below:

8. การรับประกัน

The Nissan PITWORK Oil Filter AY100-NS004 comes with a warranty period of 1 year after vehicle installation. This warranty is valid for up to 20,000 กิโลเมตร of driving. Please note that this warranty excludes wear and tear components or damage resulting from improper installation or misuse.

9. การสนับสนุน

For further assistance, technical inquiries, or troubleshooting, please contact your authorized Nissan service center or a qualified automotive technician. Always refer to your vehicle's official documentation for specific maintenance requirements and procedures.