การแนะนำ
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
ข้อมูลด้านความปลอดภัย
- อย่าวางเครื่องสแกนไว้ในที่ที่มีอุณหภูมิสูง ความชื้นสูง หรือแสงแดดโดยตรง
- หลีกเลี่ยงการทำเครื่องสแกนเนอร์ตกหรือได้รับแรงกระแทกรุนแรง
- ห้ามเปิดหรือดัดแปลงเครื่องสแกนเนอร์ด้วยตนเอง โปรดส่งต่อเครื่องสแกนให้กับช่างผู้ชำนาญการเท่านั้น
- Use only the power supply and cables provided or approved by Intermec.
- Keep the scanning window clean to ensure accurate barcode reading.
เนื้อหาแพ็คเกจ
ตรวจสอบว่าแพ็คเกจของคุณมีรายการต่อไปนี้:
- Intermec SR30 Linear Imager Barcode Scanner
- สายเคเบิลอินเทอร์เฟซ RS232
- หน่วยจ่ายไฟ
- Documentation (this manual or similar)
หากมีรายการใดขาดหายหรือเสียหาย โปรดติดต่อซัพพลายเออร์ของคุณทันที
การตั้งค่า
1. การเชื่อมต่อสแกนเนอร์
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Connect to Scanner: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- เชื่อมต่อพาวเวอร์ซัพพลาย: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. เปิดเครื่องครั้งแรก
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
การใช้งานเครื่องสแกนเนอร์
1. การสแกนบาร์โค้ด
- จุดมุ่งหมาย: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- สแกน: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- การยืนยัน: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. การทำความเข้าใจตัวชี้วัด
- ไฟ LED สีเขียว: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
การซ่อมบำรุง
การทำความสะอาดสแกนเนอร์
- ทำความสะอาดช่องสแกนเป็นประจำด้วยผ้าเนื้อนุ่มที่ไม่เป็นขุยampชุบด้วยน้ำหรือน้ำยาทำความสะอาดอ่อนๆ ที่ไม่กัดกร่อน
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- โปรดตรวจสอบให้แน่ใจว่าได้ปิดเครื่องสแกนเนอร์ก่อนทำการทำความสะอาด
พื้นที่จัดเก็บ
เมื่อไม่ใช้งาน ควรเก็บเครื่องสแกนไว้ในที่สะอาดและแห้ง หลีกเลี่ยงแสงแดดโดยตรงและอุณหภูมิที่สูงหรือต่ำเกินไป
การแก้ไขปัญหา
| ปัญหา | สาเหตุที่เป็นไปได้ | สารละลาย |
|---|---|---|
| เครื่องสแกนเนอร์ไม่สามารถเปิดเครื่องได้ | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| เครื่องสแกนไม่สามารถอ่านบาร์โค้ดได้ | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
ข้อมูลจำเพาะ
- แบบอย่าง: เอสอาร์30
- หมายเลขชิ้นส่วน: 225-727-003 (Kit)
- ประเภทเครื่องสแกนเนอร์: ตัวสร้างภาพเชิงเส้น
- อินเทอร์เฟซ: อาร์เอส232
- ผู้ผลิต: อินเตอร์เมค
- น้ำหนักสินค้า: 0.01 ounces (approximate, scanner only)
- แผนก: บาร์โค้ด
- ASIN: B003T0WF3S
การรับประกันและการสนับสนุน
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webไซต์ โปรดเก็บใบเสร็จรับเงินไว้เป็นหลักฐานการซื้อสำหรับการเรียกร้องการรับประกัน
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.