คู่มือการใช้งานและคำแนะนำการเปลี่ยนฟอยล์และใบมีดสำหรับเครื่องโกนหนวด Braun Series 1 11B

การแนะนำ

This instruction manual provides essential information for the proper installation and maintenance of your Braun Series 1 11B Shaver Foil & Cutter replacement part. To ensure optimal performance and longevity of your Braun shaver, it is crucial to use genuine replacement parts and follow these guidelines carefully. This replacement part is designed for Braun Series 1 Type 5685 shavers, including models 11B and 150.

ข้อมูลด้านความปลอดภัย

• ห้ามใช้ใกล้น้ำ
• เก็บให้ห่างจากแหล่งความร้อนและเปลวไฟ
• ถอดปลั๊กและปล่อยให้เย็นลงก่อนทำความสะอาดทุกครั้ง
• Be cautious when using on sensitive skin to avoid cuts and irritation.

Identifying Your Shaver Type

Before installing your new foil and cutter, it is critical to confirm your shaver's type number to ensure compatibility. The type number is a four-digit code, typically starting with '5', and is usually located on the shaver body. Refer to the video below for guidance on locating this number.

For some models, the type number may be found by sliding up the trimmer on the back or front of the shaver, revealing small printed numbers in the track. For newer models, you might need to remove the shaving head to find the numbers inside the head's compartment. Good lighting and magnification may be necessary to read these small markings.

คำแนะนำในการติดตั้ง

Follow these steps to replace the foil and cutter on your Braun Series 1 shaver:

1. การตระเตรียม: Ensure your shaver is turned off and unplugged from any power source.
2. ถอดชิ้นส่วนเก่าออก: Gently press the release buttons (if present) or pull the old foil and cutter block upwards to detach it from the shaver head. Dispose of the old part responsibly.
3. ติดตั้งชิ้นส่วนใหม่: Align the new Braun Series 1 11B foil and cutter block with the shaver head. Press down firmly until it clicks into place. Ensure it is securely seated.
4. ตรวจสอบความพอดี: Verify that the new foil and cutter are properly aligned and do not wobble.

คำแนะนำการใช้งาน

Once the new foil and cutter are correctly installed, your Braun Series 1 shaver is ready for use. Operate the shaver according to the original instructions provided with your shaver model. The new foil and cutter are designed to restore your shaver's cutting performance to its original standard.

การซ่อมบำรุง

Regular cleaning of your shaver's foil and cutter is essential for maintaining performance and hygiene. After each use, remove the foil and cutter block and rinse it under warm running water. For a more thorough cleaning, use a small brush to remove any trapped hair particles. Allow the parts to air dry completely before reattaching them to the shaver.

Braun recommends replacing the foil and cutter block every 18 months to maintain 100% shaving performance. This ensures that the cutting elements remain sharp and efficient, providing a close and comfortable shave.

การแก้ไขปัญหา

• ชิ้นส่วนไม่พอดี: Double-check your shaver's type number against the compatibility information for the 11B replacement part. Ensure you have a Braun Series 1 Type 5685 shaver.
• ประสิทธิภาพลดลง: Ensure the foil and cutter are clean and free of debris. If performance is still unsatisfactory after cleaning and correct installation, verify the authenticity of the replacement part.
• Irritation During Shaving: Ensure the foil is not damaged or bent. A damaged foil can cause skin irritation. Replace immediately if damage is observed.

ข้อมูลจำเพาะผลิตภัณฑ์

การรับประกันและการสนับสนุน

For warranty information or further assistance, please refer to the documentation included with your original Braun shaver or visit the official Braun website. For specific inquiries regarding this replacement part, please contact Braun customer support.