คู่มือผู้ใช้จอแสดงผล LCD สำหรับจักรยานไฟฟ้า รุ่น YL81F และตัวควบคุมมอเตอร์ไร้แปรงถ่าน รุ่น X035-AAM002

การแนะนำ

This manual provides detailed instructions for the installation, operation, and maintenance of your YOLIN YL81F E-bike LCD Display and X035-AAM002 Brushless Motor Controller. Please read this manual thoroughly before use to ensure proper function and safety.

Important Note: The YL81F color LCD display uses specific communication protocols. Different brands of e-bikes may have different LCD protocols. It is crucial to confirm the correct LCD protocol for your e-bike with customer service before purchasing to ensure compatibility. Failure to do so may result in the display not matching your e-bike system.

ข้อมูลจำเพาะ

YL81F Smart LCD Bezel-less Meter

X035-AAM002 Brushless Motor Controller

การติดตั้งและการตั้งค่า

This section outlines the steps for connecting the YL81F display and X035-AAM002 controller to your e-bike conversion kit. Ensure all connections are secure before powering on the system.

ส่วนประกอบมากกว่าview

แผนผังการเดินสายไฟ

Refer to the diagram below for correct wiring connections. Each numbered point corresponds to a specific component or function.

1. ติดตั้งจอแสดงผล: Securely attach the YL81F display to your e-bike handlebars using the provided bracket.
2. ติดตั้งคอนโทรลเลอร์: Find a suitable, protected location on your e-bike frame for the X035-AAM002 controller. Ensure it is away from direct water exposure and physical impact.
3. Connect the Main Cable: Connect the E-bike Main Cable (1) from the controller to your e-bike's main wiring harness.
4. เชื่อมต่อสายมอเตอร์: Connect the Motor Hall (2) and Motor Cables (3, 4, 9) from the controller to your e-bike motor. Ensure phase wires and Hall sensor wires are correctly matched.
5. Connect Boost Sensors: Attach the Boost Sensors (5) to your e-bike's pedal assist system.
6. เชื่อมต่อแบตเตอรี่: Connect the Battery Positive (6) and Battery Negative (10) cables from the controller to your e-bike battery. Double-check polarity.
7. เชื่อมต่ออุปกรณ์เสริม: Connect the Tachymeter Signal (7) and Brake Light/Tail Light (8) if applicable to your e-bike's accessories.
8. เชื่อมต่อจอแสดงผล: Connect the 5-Pin common plug from the YL81F display to the corresponding port on the X035-AAM002 controller.
9. รักษาความปลอดภัยการเชื่อมต่อทั้งหมด: Ensure all connectors are firmly seated and secured to prevent accidental disconnection during riding.

คำแนะนำการใช้งาน

YL81F LCD Display Functions

The YL81F display provides comprehensive information and control over your e-bike system:

• Electricity Display: Shows current battery charge level.
• Auxiliary Gear Adjustment and Indication: Allows selection and display of pedal-assist levels.
• จอแสดงความเร็ว: Shows real-time speed, maximum speed, and average speed.
• จอแสดงระยะทาง: Tracks single trip mileage and total accumulated mileage.
• Auxiliary Push Control and Indication: Activates and indicates walk-assist mode.
• การควบคุมและแสดงสัญญาณไฟหน้า: Controls and indicates the status of your e-bike's headlights.
• การแสดงรหัสข้อผิดพลาด: Shows error codes for system diagnostics.
• Engine Power Display: Indicates the current power output of the motor.
• USB Connection Indication: Shows when a USB device is connected (e.g., for charging).
• Cruise Control Indication: Indicates when cruise control is active.
• Bluetooth Connection Indication: Shows Bluetooth connectivity status.
• การตั้งค่าพารามิเตอร์ส่วนบุคคล: Access settings for wheel diameter, speed limit, battery power, booster parameters, power-on password, and controller current limit.
• Factory Default Parameter Recovery: Option to restore all settings to factory defaults.

X035-AAM002 Controller Features

The X035-AAM002 controller incorporates several intelligent features for enhanced performance and safety:

• Invisible Soft/Hard Start: To switch between soft and hard start modes: Tighten the brake, turn the throttle handle to the bottom, turn on the power, and wait for 3 seconds. The system will switch to smooth start (default is hard start). This setting has a memory function. Repeat the operation to switch back.
• Invisible Single/Dual Hall Ampเครื่องฟอก: To switch between single and dual Hall boost modes (for 3-wire booster sensors only): Apply the brake, turn on the power, and turn the wheel/loop three times. The system will switch to Dual Hall Boost (default is only Hall Boost). This setting has a memory function. Repeat the operation to switch back.
• การป้องกันไฟ: Automatically stops output when the battery voltage ลดลงต่ำกว่า under-voltage threshold, protecting the battery from over-discharge.
• Anti-Stealing Power On: Prevents unintended power-on due to line or throttle malfunctions, enhancing vehicle security.
• MOS Tube Short Circuit Protection: Detects MOS tube defects upon power-on to prevent damage to other components from serial short circuits.
• การป้องกันอุณหภูมิสูง: Reduces output current or stops output automatically if the controller temperature becomes too high.
• Rotation Protection: If the motor is blocked, the controller automatically limits current and cuts off the circuit within 2 seconds to protect both the motor and the controller.

การซ่อมบำรุง

Regular maintenance ensures the longevity and optimal performance of your e-bike display and controller:

• การทำความสะอาด: Keep the display and controller clean from dust and dirt. Use a soft, damp ใช้ผ้าสำหรับทำความสะอาด หลีกเลี่ยงสารเคมีรุนแรงหรือวัสดุที่มีฤทธิ์กัดกร่อน
• การตรวจสอบการเชื่อมต่อ: Periodically inspect all electrical connections for tightness and signs of wear or corrosion. Ensure waterproof connectors are properly sealed.
• ความสมบูรณ์ของสายเคเบิล: Check all cables for cuts, pinches, or damage. Replace any damaged cables immediately.
• การปกป้องสิ่งแวดล้อม: While the components are designed for outdoor use, avoid prolonged exposure to extreme weather conditions (heavy rain, direct sunlight, extreme cold) when possible.

การแก้ไขปัญหา

This section provides guidance on common issues you might encounter. For complex problems, consult a qualified technician.

ปัญหาการแสดงผล

• จอแสดงผลไม่เปิด:
  • ตรวจสอบการเชื่อมต่อแบตเตอรี่และระดับการชาร์จ
  • Ensure the 5-Pin connection cable between the display and controller is securely attached.
  • Verify the e-bike's main power switch is on.
• การอ่านค่าความเร็ว/ระยะทางไม่ถูกต้อง:
  • Check the wheel diameter setting in the display's personalized parameters.
  • Ensure the tachymeter signal wire (7) is correctly connected.
• Fault Codes Displayed:
  • Note down the fault code and refer to your e-bike's specific fault code list (if available) or contact customer support for diagnosis.

ปัญหาเกี่ยวกับตัวควบคุม

• มอเตอร์ไม่ตอบสนอง:
  • Check all motor cable (2, 3, 4, 9) and Hall sensor connections.
  • ตรวจสอบปริมาณแบตเตอรี่tage is above the under-voltage เกณฑ์การป้องกัน
  • Check for any fault codes on the display.
• Intermittent Power/Motor Cut-off:
  • Could be due to high temperature protection; allow the controller to cool down.
  • ตรวจสอบการเชื่อมต่อที่หลวมหรือสายไฟชำรุดเสียหาย
  • Ensure the motor is not blocked, triggering rotation protection.

เคล็ดลับสำหรับผู้ใช้

• Protocol Verification: As highlighted in the introduction, always verify the LCD protocol compatibility with your e-bike's existing system before installation. This is the most common reason for incompatibility.
• เนื้อหาแพ็คเกจ: The product package typically includes the YL81F display, the X035-AAM002 controller, and a connection cable. Ensure all components are present upon receipt.
• Soft/Hard Start Customization: Utilize the controller's 'Invisible Soft/Hard Start' feature to tailor your e-bike's acceleration response to your preference.
• Hall Sensor Configuration: If your e-bike uses a 3-wire booster sensor, you can adjust the Hall amplifier mode for optimal pedal assist.

การรับประกันและการสนับสนุน

For any questions regarding the YL81F LCD Display or X035-AAM002 Brushless Motor Controller, including technical support, troubleshooting, or warranty claims, please contact the seller or manufacturer directly. Always provide your product model numbers (YL81F and X035-AAM002) and a detailed description of the issue for efficient assistance.