Universal Multi-Frequency Remote Control Duplicator

1. บทนำ

This manual provides detailed instructions for the setup, operation, and maintenance of your Aubess Universal Multi-Frequency Remote Control Duplicator. This device is designed to copy existing remote control signals for various applications, including garage doors, electric gates, car alarms, and home security systems. It supports both 315MHz and 433MHz frequencies.

Figure 1: Universal Remote Control Duplicator

2. ข้อมูลจำเพาะ

รูปที่ 2: ขนาดของรีโมทคอนโทรล

3. เนื้อหาบรรจุภัณฑ์

• 1 x Universal Remote Control Duplicator
• 1 x 27A Battery (pre-installed)

4. การตั้งค่าและการเขียนโปรแกรม

Before programming, ensure your original remote control is functional and that its chip type and frequency are compatible with this duplicator. This remote can copy fixed codes and learning codes, but not rolling/stealth codes.

4.1 Identifying Frequency and Chip Type

To determine the frequency and chip model of your original remote, you may need to open it (usually with a small screwdriver) and check the numbers printed on the components on the motherboard. Look for crystal oscillator frequencies (e.g., 315 or 433) and chip model numbers.

Compatible Chip Models:

• 2260 (all manufacturers)
• 2262 (all manufacturers)
• PT2264, 5326 (all manufacturers)
• SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014
• SMC918 series, 527 (all manufacturers)
• 1527 (all manufacturers)
• 2240 (all manufacturers)
• HCS101, HCS200/HCS201 (part code)
• HCS300/HCS301 (part code)
• Part single chip microcomputer
• PT2262, PT2240, PT2264, PT2260, PT2242, AX5326-4, AX5326-3, SC2262, SC2260, HS2262, LX2262, EV1527, P527

Compatible Crystal Frequencies: 315เมกะเฮิรตซ์, 433เมกะเฮิรตซ์

4.2 Code Cleaning Method

Before copying, you must clear any existing codes from the duplicator remote:

1. Simultaneously press and hold the two top buttons (usually 'A' and 'B', or 'Lock' and 'Unlock').
2. The LED indicator light will begin to flash rapidly.
3. Once the light flashes quickly three times and then stops, all data in the memory is cleared.
4. After clearing, pressing any button on the duplicator remote will not illuminate the LED, indicating it's ready for copying.

4.3 Copy Method

To copy a signal from your original remote to the duplicator:

1. Hold your original remote control in one hand and the duplicator remote in the other.
2. Position the two remote controls as close as possible to each other. Ideally, place them side-by-side on a flat surface with zero distance between them.
3. Press and hold the desired button on your original remote (e.g., 'A').
4. Simultaneously, press and hold the corresponding button on the duplicator remote where you want to store the code (e.g., 'A').
5. Keep both buttons pressed until the LED indicator light on the duplicator remote flashes quickly after three initial flashes. This indicates successful copying.
6. ปล่อยปุ่มทั้งสอง
7. ทำซ้ำขั้นตอนนี้สำหรับปุ่มอื่นๆ ที่คุณต้องการคัดลอก

บันทึก: Some original remotes may have lower transmitting power. If copying is unsuccessful, try placing the original remote directly against the duplicator remote. Avoid operating in areas with significant signal interference. If copying fails, repeat the code cleaning process and try again.

Figure 3: Remote Control Programming Process

5. การใช้งานรีโมทคอนโทรล

Once programmed, the duplicator remote functions identically to your original remote. Simply press the corresponding button (A, B, C, or D) that you have programmed to activate the desired function (e.g., open/close gate, arm/disarm alarm).

6. การบำรุงรักษา

6.1 การเปลี่ยนแบตเตอรี่

The remote control is powered by a DC12V 27A battery. If the remote's range decreases significantly or the LED indicator light does not illuminate, it may be time to replace the battery. To replace:

1. เปิดรีโมทคอนโทรลอย่างระมัดระวังasing (a small screwdriver may be needed).
2. Remove the old 27A battery.
3. Insert a new DC12V 27A battery, ensuring correct polarity.
4. ปิดรีโมทคอนโทรลasinก. อย่างปลอดภัย

6.2 การดูแลทั่วไป

• Keep the remote control dry and away from extreme temperatures.
• หลีกเลี่ยงการทำรีโมทตกหรือโดนแรงกระแทกรุนแรง
• Clean the remote with a soft, dry cloth. Do not use harsh chemicals or solvents.

7 การแก้ไขปัญหา

• Remote not copying:
  • Ensure your original remote is working correctly.
  • Verify that the chip type and frequency of your original remote are compatible with this duplicator (refer to Section 4.1).
  • Make sure the duplicator remote's code has been cleared successfully before attempting to copy (refer to Section 4.2).
  • Ensure the original and duplicator remotes are placed very close to each other during the copying process.
  • Try repeating the code cleaning and copying steps.
  • Check for strong signal interference in the area.
• Copied remote not working:
  • Confirm that the copying process was successful (LED flashed rapidly).
  • Check the battery in the duplicator remote.
  • Ensure the target device (e.g., gate opener) is within the remote's operating range.
  • Verify that your original remote is not a rolling code (also known as stealth code) type, as these cannot be copied.
• Compatibility with specific systems (e.g., Merik 511, Rossi motor):
  • Compatibility depends on the chip model and operating frequency of your specific system's remote. You must verify these details against the compatible list in Section 4.1.
  • If your system uses a rolling code, this duplicator will not be compatible.

8. เคล็ดลับผู้ใช้

• Always verify compatibility: ก่อนการซื้อasing or attempting to copy, confirm that your original remote's chip and frequency are listed as compatible.
• Optimal copying environment: Perform the copying process in a quiet area, free from electronic interference, and ensure the remotes are in direct contact.
• Test thoroughly: After copying, test all programmed buttons multiple times to ensure reliable operation.

9. การรับประกันและการสนับสนุน

For any issues or further assistance, please contact the seller or refer to the product listing for warranty information. Keep your purchase receipt as proof of purchase.