RODOT DC 12V 1CH RF Wireless Relay Module Instruction Manual

1. บทนำ

The RODOT DC 12V 1CH RF Wireless Relay Module is a versatile remote control switch designed for various industrial and security applications. It offers stable and reliable performance with high receive sensitivity, allowing signals to pass through walls, floors, and doors. The maximum range is up to 164ft/50m in open areas. This module is compatible with EV1527 learning code remote controls operating at 433Mhz.

2. เนื้อหาบรรจุภัณฑ์

แพ็คเกจนี้ประกอบด้วยส่วนประกอบต่อไปนี้:

• 2 x 1-Button Transmitters (Remote Controls)
• 1 x 1CH Receiver Module
• 1 x Receiver Shell

ภาพ: เนื้อหาภายในบรรจุภัณฑ์ของผลิตภัณฑ์

3. สินค้าหมดview

The system consists of a receiver module and remote controls. The receiver module is designed for easy integration into various setups, providing terminals for power input and relay output. The remote controls allow for flexible operation of the connected devices.

Image: The receiver module and two remote controls.

ภาพ: รายละเอียด view of the receiver module's terminals.

4. ข้อมูลจำเพาะ

5. การติดตั้งและการเดินสายไฟ

The receiver module requires a 12V DC power supply. Ensure correct polarity when connecting power. The module provides Normally Open (NO), Common (COM), and Normally Closed (NC) terminals for connecting your device.

แผนผังการเดินสายไฟ

Refer to the diagram below for typical wiring configurations. The power supply for the connected device can be any voltage, as the relay only controls the circuit's switch.

Image: Wiring diagram for the receiver module.

คำจำกัดความของเทอร์มินัล:

• คอม: Common terminal of the relay.
• เลขที่: Normally Open terminal of the relay. When the relay is not working, NO is disconnected from COM.
• เอ็นซี: Normally Closed terminal of the relay. When the relay is not working, NC is connected to COM.
• วี+: 12V Positive input.
• วี-: 12V Negative input.

6. Operating Modes & Pairing

The relay module supports several operating modes, which can be configured by pressing the learning button on the receiver module a specific number of times. Always clear previous pairings before setting a new mode.

Clearing Paired Remote Controls:

Press the learning button 8 times. The indicator LED will flash, confirming all previously paired remote controls have been cleared.

Setting Operating Modes:

After clearing, press the learning button the specified number of times for your desired mode, then press a button on your remote control to pair.

• โหมดชั่วขณะ: Press the learning button 1 time. Press and hold the remote button to turn ON, release to turn OFF.
• โหมดสลับ: Press the learning button 2 times. Press the remote button once to turn ON, press again to turn OFF.
• โหมดสลัก: Press the learning button 3 times. (Requires a 2-button remote). Press button A to turn ON, press button B to turn OFF.
• โหมดหน่วงเวลา: Press the learning button 4, 5, 6, or 7 times for 5s, 10s, 15s, or 20s delay respectively. Press the remote button to turn ON, it will automatically turn OFF after the set delay.

Image: Visual explanation of different working modes.

โหมดชั่วขณะ

สลับโหมด

โหมดสลัก

โหมดหน่วงเวลาปิด

7 การแก้ไขปัญหา

• รีโมตไม่ตอบสนอง: Ensure the receiver module is powered correctly (12V DC). Check if the remote control is paired to the receiver. If not, follow the pairing instructions.
• ขอบเขตจำกัด: Ensure the antenna on the receiver module is extended and not obstructed. Environmental factors like thick walls or other RF interference can reduce range.
• Incorrect Mode Operation: If the relay operates unexpectedly, re-clear all paired remotes and re-pair them in the desired operating mode.
• ไฟ LED ไม่ติด: Verify the power supply connections to the receiver module. Check the LED itself for damage.

8. ข้อมูลด้านความปลอดภัย

• ควรตัดกระแสไฟก่อนทำการเดินสายไฟหรือบำรุงรักษาทุกครั้ง
• ตรวจสอบให้แน่ใจว่าการเชื่อมต่อทั้งหมดแน่นหนาเพื่อป้องกันไฟฟ้าลัดวงจร
• อย่าให้โมดูลสัมผัสกับความชื้นหรืออุณหภูมิที่สูงเกินไป
• This device is intended for low-voltage DC applications. Do not connect to AC power unless specified.

9. การรับประกันและการสนับสนุน

For any issues or questions regarding your RODOT DC 12V 1CH RF Wireless Relay Module, please contact RODOT DIY customer support. Refer to your purchase documentation for warranty details.