1. บทนำ
The Selec CH-403-2 is a precision temperature chiller controller designed for industrial and commercial applications requiring accurate temperature regulation. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your device. Please read this manual thoroughly before installation and operation.
2. ข้อมูลด้านความปลอดภัย
ปฏิบัติตามข้อควรระวังด้านความปลอดภัยต่อไปนี้เสมอเพื่อป้องกันการบาดเจ็บและความเสียหายต่ออุปกรณ์:
- ตรวจสอบให้แน่ใจว่าได้ตัดการเชื่อมต่อแหล่งจ่ายไฟแล้วก่อนที่จะดำเนินการเดินสายไฟหรือบำรุงรักษาใดๆ
- การติดตั้งและการบริการควรดำเนินการโดยบุคลากรที่มีคุณสมบัติเท่านั้น
- ตรวจสอบว่าแหล่งจ่ายไฟมีแรงดันไฟtage ตรงตามข้อกำหนดของตัวควบคุม
- Do not expose the controller to excessive moisture, dust, or corrosive gases.
- ตรวจสอบให้แน่ใจว่ามีการต่อสายดินอย่างเหมาะสมเพื่อป้องกันไฟฟ้าช็อต
3. การตั้งค่า
3.1 การแกะกล่อง
Carefully remove the controller from its packaging. Inspect the device for any signs of damage during transit. Report any damage to your supplier immediately.
3.2 การติดตั้ง
The CH-403-2 is designed for panel mounting. Cut an opening of 45mm x 45mm (1.77" x 1.77") in the panel. Insert the controller into the opening and secure it using the provided mounting clamps. Ensure a snug fit to prevent dust and moisture ingress.
3.3 การเชื่อมต่อสายไฟ
Refer to the wiring diagram located on the side of the controller or in the detailed technical specifications. Ensure all connections are secure and correct before applying power.
- แหล่งจ่ายไฟ: เชื่อมต่อสายไฟ AC ที่เหมาะสมtage (e.g., 230V AC) to the designated power terminals.
- อินพุตเซนเซอร์: Connect the temperature sensor (e.g., NTC, PT100) to the sensor input terminals. Observe polarity if applicable.
- เอาต์พุตควบคุม: Connect the chiller or heating element to the relay output terminals. Ensure the load current does not exceed the relay's maximum rating.
- เอาต์พุตสัญญาณเตือน (ตัวเลือกเสริม): If applicable, connect external alarm devices to the alarm output terminals.
3.4 การเพิ่มพลังเริ่มต้น
After all connections are verified, apply power to the controller. The display should illuminate, showing the current temperature and default settings.
4. ปฏิบัติการ
4.1 แสดงผลเกินview
The front panel features a digital display showing the process value (PV) and set point (SV), along with indicator LEDs for output status (e.g., ON/OFF, Alarm).
4.2 ฟังก์ชันปุ่ม
- ปุ่ม ตลท.: ใช้สำหรับเข้าสู่โหมดการตั้งค่าพารามิเตอร์และยืนยันการเลือก
- ปุ่มขึ้น/ลง: ใช้สำหรับเลื่อนดูพารามิเตอร์และปรับค่าต่างๆ
- ปุ่มโหมด: Used to switch between display modes or access advanced settings.
4.3 Setting Temperature Setpoint (SV)
- กดปุ่ม ชุด button once. The SV value will flash.
- ใช้ UP or ลง buttons to adjust the setpoint to the desired temperature.
- กดปุ่ม ชุด button again to confirm the new setpoint. The display will return to showing the PV.
4.4 การกำหนดค่าพารามิเตอร์
To access advanced parameters such as hysteresis, calibration offset, or delay times, press and hold the ชุด button for several seconds until the first parameter code appears. Use the ขึ้น/ลง buttons to navigate through parameters and the ชุด button to select and modify values. Refer to the detailed parameter list in the full technical manual for specific codes and ranges.
5. การบำรุงรักษา
5.1 การทำความสะอาด
Clean the front panel of the controller periodically with a soft, damp ผ้า อย่าใช้น้ำยาทำความสะอาดหรือตัวทำละลายที่มีฤทธิ์กัดกร่อน เพราะอาจทำให้หน้าจอเสียหายหรือasing. ตรวจสอบให้แน่ใจว่าไม่มีของเหลวเข้าไปในอุปกรณ์
5.2 การตรวจสอบตามปกติ
- ตรวจสอบการเชื่อมต่อสายไฟว่าหลวมหรือมีสนิมหรือไม่
- Verify the temperature sensor is clean and properly installed.
- Check for any unusual noises or smells from the controller or connected equipment.
5.3 การสอบเทียบ
If temperature readings appear inaccurate, the sensor or controller may require calibration. Refer to the advanced parameter settings for sensor offset adjustment. For precise calibration, consult a qualified technician.
6 การแก้ไขปัญหา
ส่วนนี้จะกล่าวถึงปัญหาทั่วไปที่คุณอาจพบ สำหรับปัญหาที่ไม่ได้ระบุไว้ในที่นี้ โปรดติดต่อฝ่ายสนับสนุนด้านเทคนิค
| ปัญหา | สาเหตุที่เป็นไปได้ | สารละลาย |
|---|---|---|
| No display / Power off | ไม่มีแหล่งจ่ายไฟ; การเดินสายไฟไม่ถูกต้อง; ฟิวส์ขาด | ตรวจสอบการเชื่อมต่อสายไฟ; ตรวจสอบระดับเสียงtage; Replace fuse if necessary. |
| การอ่านอุณหภูมิไม่ถูกต้อง | Sensor faulty; Sensor wiring incorrect; Calibration offset needed | Check sensor connections; Replace sensor; Adjust calibration offset in parameters. |
| เอาต์พุตไม่สลับ | Setpoint not reached; Hysteresis setting too wide; Output relay faulty | Verify setpoint and current temperature; Adjust hysteresis; Test output relay (by qualified personnel). |
| Error Code 'E1' | วงจรเปิดเซนเซอร์ | Check sensor wiring for breaks; Replace sensor. |
| Error Code 'E2' | เซ็นเซอร์ลัดวงจร | Check sensor wiring for shorts; Replace sensor. |
7. ข้อมูลจำเพาะ
| พารามิเตอร์ | ค่า |
|---|---|
| แบบอย่าง | บทที่ 403-2 |
| ประเภทอินพุต | NTC / PT100 (selectable) |
| ช่วงอุณหภูมิ | -50°C to 150°C (sensor dependent) |
| เอาต์พุตควบคุม | 1 x Relay (NO/NC), 5A @ 250V AC resistive |
| เอาต์พุตเสริม | 1 x Relay (NO), 3A @ 250V AC resistive (Alarm) |
| ปริมาณอุปทานtage | 230V AC ±10%, 50/60 Hz |
| ความแม่นยำ | ±1% of full scale ±1 digit |
| แสดง | LED 3- หลัก |
| การติดตั้ง | Panel Mount (45x45mm cutout) |
| อุณหภูมิในการทำงาน | 0°C ถึง 50°C |
| ขนาด (กxสxล) | 48มม. x 48มม. x 85มม. |
8. การรับประกันและการสนับสนุน
Selec products are covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Selec website. For technical support, service, or spare parts, please contact your authorized Selec distributor or customer service department, providing your product model number (CH-403-2) and serial number.