EPEVER Tracer4210AN

คู่มือผู้ใช้ EPEVER Tracer4210AN 40A MPPT Solar Charge Controller

Model: Tracer4210AN | Brand: EPEVER

1. บทนำและเรื่องอื่นๆview

The EPEVER Tracer4210AN is a 40A MPPT (Maximum Power Point Tracking) solar charge controller designed for 12V and 24V DC systems. It efficiently regulates power from solar panels to charge various battery types, including lead-acid (Sealed, AGM, GEL, Flooded) and lithium (LiFePO4, Li(NiCoMn)O2) batteries. This controller features an advanced MPPT control algorithm for high tracking and conversion efficiency, ensuring optimal energy harvest from your solar array. It includes multiple built-in protections for safe and stable operation, and an LCD screen for easy monitoring and parameter customization.

ด้านหน้า view of the EPEVER Tracer4210AN 40A MPPT Solar Charge Controller.

รูปที่ 1.1 : ด้านหน้า View of the EPEVER Tracer4210AN Controller.

กลับ view of the EPEVER Tracer4210AN 40A MPPT Solar Charge Controller, showing the heat sink.

รูปที่ 1.2: ย้อนกลับ View of the EPEVER Tracer4210AN Controller.

2. ข้อมูลด้านความปลอดภัย

Before installing or operating the EPEVER Tracer4210AN solar charge controller, please read all instructions carefully. Improper installation or operation can lead to equipment damage, personal injury, or property damage. Always ensure proper ventilation around the controller. Do not expose the controller to water or excessive humidity. Disconnect all power sources before performing any maintenance or adjustments.

ลำดับการเชื่อมต่อที่สำคัญ: Always connect the battery first, then the load, and finally the solar panel. When disconnecting, reverse this order: disconnect the solar panel, then the load, and finally the battery.

3. คุณสมบัติของผลิตภัณฑ์

  • Advanced MPPT control algorithm for tracking efficiency greater than 98% and peak conversion efficiency of 99.5%.
  • Automatic identification of 12V/24V DC system voltage.
  • Supports various battery types: Lead-acid (Sealed, AGM, GEL, Flooded) and Lithium (LiFePO4, Li(NiCoMn)O2, User-defined).
  • Built-in multiple protections: PV over-voltage แบตเตอรี่เกินปริมาตรtage, over-temperature, over-charging, short-circuit, reverse polarity, and temperature compensation.
  • Informative LCD screen and two buttons for customizable parameters and display of working status.
  • 4 วินาทีtage battery charging (Bulk, Boost, Float, and Equalization).
  • Common negative grounded design.
EPEVER Tracer4210AN MPPT efficiency diagram showing 99.5% tracking efficiency and 98% charge conversion efficiency.

Figure 3.1: MPPT Tracking and Charge Conversion Efficiency.

EPEVER Tracer4210AN showing multiple protection features like PV over current, battery over voltage, short circuit, and reverse polarity.

Figure 3.2: Multiple Protection Features of the Controller.

4. เนื้อหาบรรจุภัณฑ์

The package for your EPEVER Tracer4210AN solar charge controller typically includes:

  • EPEVER Tracer4210AN MPPT Solar Charge Controller
  • คู่มือการใช้งาน
  • ใบรับรองคุณภาพ
  • Small green connector (for temperature sensor)

วิดีโอ 4.1: แกะกล่องและอื่นๆview of the EPEVER Tracer-AN Series MPPT Solar Charge Controller (demonstrated with a Tracer3210AN model), showing package contents and physical features.

5. การตั้งค่าและการติดตั้ง

Follow these steps for proper installation. Always ensure correct polarity and secure connections to prevent damage.

  1. เชื่อมต่อแบตเตอรี่: Loosen the screws on the battery terminals of the controller. Connect the positive (+) and negative (-) battery cables to the corresponding terminals. Ensure the connection is secure. The controller will automatically detect the system voltagอี (12V/24V).
  2. เชื่อมต่อโหลด: Loosen the screws on the load terminals. Connect the positive (+) and negative (-) load cables to the corresponding terminals.
  3. เชื่อมต่อแผงโซล่าเซลล์: Loosen the screws on the solar panel (PV) terminals. Connect the positive (+) and negative (-) solar panel cables to the corresponding terminals.
  4. เชื่อมต่อเซ็นเซอร์วัดอุณหภูมิ (ไม่จำเป็น): Insert the remote temperature sensor into the designated port on the controller. This allows for accurate battery temperature compensation during charging.

สำคัญ: Always connect the battery first, then the load, and finally the solar panel. When disconnecting, reverse this order: disconnect the solar panel, then the load, and finally the battery.

Connection diagram for EPEVER Tracer4210AN showing solar panel, battery, and DC load connections.

Figure 5.1: Basic Connection Diagram for the Solar Charge Controller.

EPEVER Tracer4210AN showing supported battery types: Lithium, Sealed, Flooded, Gel, AGM.

Figure 5.2: Supported Battery Types for the Controller.

6. คู่มือการใช้งาน

The controller features an LCD display and two buttons ("SELECT" and "ENTER") for monitoring system status and configuring parameters.

6.1 จอแสดงผล LCD และฟังก์ชันปุ่ม

หน้าจอ LCD จะแสดงพารามิเตอร์ต่างๆ ของระบบ เช่น ปริมาณแบตเตอรี่tage, charging current, load current, and temperature. Use the "SELECT" button to browse through different display interfaces and the "ENTER" button to confirm selections or enter settings mode.

EPEVER Tracer4210AN LCD display showing PV voltage, ปริมาณแบตเตอรี่tagและสถานะการโหลด

Figure 6.1: LCD Display showing system parameters.

6.2 การตั้งค่าประเภทแบตเตอรี่

การตั้งค่าประเภทแบตเตอรี่:

  1. Press the "ENTER" button and hold for 5 seconds under the battery voltagอีอินเทอร์เฟซ
  2. Press the "SELECT" button when the battery type interface is flashing to cycle through available battery types (SEL, GEL, FLD, LiFePO4, Li(NiCoMn)O2, USE).
  3. กดปุ่ม "ENTER" เพื่อยืนยันประเภทแบตเตอรี่ที่เลือก
Diagram showing steps to set battery type on the EPEVER Tracer4210AN LCD.

Figure 6.2: Steps for Setting Battery Type via LCD.

6.3 การตั้งค่าโหมดการทำงานของโหลด

To set the load working mode:

  1. Press the "ENTER" button and hold for 5 seconds under the load mode interface.
  2. Press the "SELECT" button when the load mode interface is flashing to choose the desired mode.
  3. Press the "ENTER" button to confirm the load mode.

คำเตือน: Setting Light ON/OFF, Test mode, and Manual mode via Timer1. Timer2 will be disabled and display "2n".

7. การบำรุงรักษา

Regular maintenance ensures optimal performance and longevity of your solar charge controller. Perform the following checks periodically:

  • ทำความสะอาดตัวควบคุม: รักษาตัวควบคุมให้สะอาด ปราศจากฝุ่นและสิ่งสกปรก ใช้ผ้าแห้งเช็ดทำความสะอาดพื้นผิว
  • ตรวจสอบการเชื่อมต่อ: Periodically inspect all wiring connections (solar panel, battery, load) to ensure they are tight and free from corrosion. Loose connections can cause overheating and damage.
  • ตรวจสอบความเสียหาย: Check for any visible signs of damage to the controller, cables, or terminals.
  • ตรวจสอบการระบายอากาศ: Ensure that the controller's heat sink and ventilation openings are not blocked to allow for proper heat dissipation.

8 การแก้ไขปัญหา

If you encounter issues with your EPEVER Tracer4210AN, refer to the following general troubleshooting tips. For detailed error codes and solutions, consult the full user manual provided with the product.

  • ไม่มีจอแสดงผล/พลังงาน: ตรวจสอบการเชื่อมต่อแบตเตอรี่และตรวจสอบให้แน่ใจว่าแบตเตอรี่มีกำลังไฟเพียงพอtage. Verify all fuses in the system.
  • ไม่มีการชาร์จ: Ensure solar panels are connected correctly and receiving sunlight. Check PV voltage and current on the LCD. Verify battery type settings.
  • โหลดไม่ทำงาน: Check load connections and ensure the load is within the controller's rated current. Verify load working mode settings.
  • เกินปริมาณtage/ต่ำกว่าฉบับtage สัญญาณเตือนภัย: ตรวจสอบปริมาณแบตเตอรี่tage and ensure it is within the safe operating range for the selected battery type.

The controller has multiple built-in protections (PV over-voltage แบตเตอรี่เกินปริมาตรtage, over-temperature, over-charging, short-circuit, reverse polarity) which may activate to protect the system. If a protection is triggered, the LCD may display an error code or indicator. Address the underlying cause before resetting or restarting the system.

9. ข้อมูลจำเพาะ

Below are the key technical specifications for the EPEVER Tracer4210AN 40A MPPT Solar Charge Controller.

EPEVER Tracer4210AN Specifications
พารามิเตอร์ค่า
แบบอย่างTracer4210AN
ระบบที่กำหนดฉบับที่tage12 / 24V อัตโนมัติ
ประเภทแบตเตอรี่Lead-acid (Sealed/Gel/Flooded)/Lithium (LiFePO4/Li(NiCoMn)O2)/User
โวลต์อินพุตแบตเตอรี่tagอี เรนจ์8~32โวลต์
กระแสไฟชาร์จที่กำหนด40เอ
จัดอันดับการปลดปล่อยปัจจุบัน40เอ
กำลังชาร์จสูงสุด520 วัตต์/12 โวลต์, 1040 วัตต์/24 โวลต์
สูงสุด ประสิทธิภาพการแปลง≥98.0%
ประสิทธิภาพการติดตาม≥99.5%
แม็กซ์ PV Open Circuit Voltage100V (at min. operating temp), 92V (at 25°C ambient temp)
MPPT ฉบับที่tagอี เรนจ์(แบตเตอรี่โวลtagจ +2V) ~ 72V
อีควอไลเซชั่นฉบับtage (Flooded)14.8โวลต์
เพิ่มปริมาณtage (Flooded)14.6โวลต์
ลอยฉบับtage (Flooded)13.8โวลต์
ปริมาณต่ำtage เชื่อมต่อใหม่ Voltage (Flooded)12.6โวลต์
ปริมาณต่ำtage ตัดการเชื่อมต่อฉบับtage (Flooded)11.1โวลต์
การบริโภคเพื่อตนเอง≤12มิลลิแอมป์
สิ่งที่แนบมาIP30
อินเทอร์เฟซการสื่อสารRS485 (อาร์เจ45)
การต่อลงดินเชิงลบทั่วไป
ช่วงอุณหภูมิในการทำงาน-25°C ~ +45°C (100% input and output)
ขนาด (กxยxส)250x180x63mm (approx. 10.8"L x 7.6"W x 3.2"H)
น้ำหนักสุทธิ1.65กก.
EPEVER Tracer4210AN dimensions: 10.83 inches length, 7.6 inches width, 3.2 inches height.

Figure 9.1: Physical Dimensions of the Controller.

10. การรับประกันและการสนับสนุน

The EPEVER Tracer4210AN Solar Charge Controller comes with a 1-year warranty. For warranty claims or technical support, please contact your vendor or EPEVER customer service.

For advanced parameter settings and monitoring, optional accessories are available:

  • เครื่องวัดระยะไกล MT50
  • eBOX-WIFI/BLE-01 (for APP monitoring)
  • CC-USB-RS485-150U cable (for PC software)
  • Remote Temperature Sensor (RTS300R47K3.81A)
EPEVER logo.

Figure 10.1: EPEVER Brand Logo.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.